fabdo
Member
habe einen neuen pc und anscheinend klappt das mit dem brenne irgendwie nicht.
beim "normalen" brach es immer ab: cdrecord zuwenig rechte.
also habe ich nun k3b als root ausgeführt, ging aber dann immer noch nicht:
wäre super wenn mir jemand helfen könnte.
beim "normalen" brach es immer ab: cdrecord zuwenig rechte.
also habe ich nun k3b als root ausgeführt, ging aber dann immer noch nicht:
Code:
Devices
-----------------------
HL-DT-ST DVDRAM GH22LS50 TL01 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]
System
-----------------------
K3b Version: 1.70.0
KDE Version: 4.4.00 (KDE 4.4.0) "release 222"
QT Version: 4.6.2
Kernel: 2.6.31.12-0.1-desktop
Used versions
-----------------------
cdrecord: 1.1.9
cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.9
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVDRAM GH22LS50 '
Revision : 'TL01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R) (current)
Profile: 0x000A (CD-RW)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive DMA Speed: 16373 kB/s 93x CD 11x DVD
FIFO size : 4194304 = 4096 KB
Speed set to 8468 KB/s
Track 01: data 678 MB
Total size: 778 MB (77:08.48) = 347136 sectors
Lout start: 778 MB (77:10/36) = 347136 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type A, high Beta category (A+) (3)
ATIP start of lead in: -11634 (97:26/66)
ATIP start of lead out: 359846 (79:59/71)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359846 Blocks current: 359846 Blocks remaining: 12710
Starting to write CD/DVD at speed 48.0 in dummy SAO mode for single session.
Last chance to quit, starting dummy write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Sending CUE sheet...
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01: 0 of 678 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 01 74 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 2A 00 00 80 30 05 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x30 Qual 0x05 (cannot write medium - incompatible format) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 761856 bytes
Writing time: 21.454s
Average write speed 216.2x.
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time: 0.004s
/usr/bin/wodim: fifo had 76 puts and 13 gets.
/usr/bin/wodim: fifo was 0 times empty and 6 times full, min fill was 92%.
cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/sr0 speed=48 -sao -dummy driveropts=burnfree -data -tsize=347136s -
wäre super wenn mir jemand helfen könnte.