Hallo,
ich habe mir die aktuelle VB von der Hompage installiert.
Wenn ich VB starte kommt folgende Meldung:
~ # VirtualBox
WARNING: The vboxdrv kernel module is not loaded. Either there is no module
available for the current kernel (2.6.27.7-9-pae) or it failed to
load. Please recompile the kernel module and install it by
sudo /etc/init.d/vboxdrv setup
You will not be able to start VMs until this problem is fixed.
WARNING: The compilation of the vboxdrv.ko kernel module failed during the
installation for some reason. Starting a VM will not be possible.
Please consult the User Manual for build instructions.
/etc/init.d/vboxdrv setup
Wenn ich den Befehl "sudo /etc/init.d/vboxdrv setup" ausführe kommt folgende Meldung:
/etc/init.d/vboxdrv setup
Stopping VirtualBox kernel module done
Recompiling VirtualBox kernel module failed
(Look at /var/log/vbox-install.log to find out what went wrong)
linux-tza2:/home/boss #
Das Programm startet dann schon.
Bei der Installation von Vista kommt dann wieder die obige Meldung "/etc/init.d/vboxdrv setup"
Im Handbuch unter Droublshooting gibt es folgenden Beitrag:
11.5 Linux hosts
11.5.1 Linux kernel module refuses to load
If the VirtualBox kernel module (vboxdrv) refuses to load, i.e. you get an “Error inserting
vboxdrv: Invalid argument”, check (as root) the output of the dmesg command
to find out why the load failed. The most common reasons are:
• With Linux 2.6.19 and higher, the NMI watchdog may be active. Add
nmi_watchdog=0 to the kernel command line (e.g. in your grub configuration)
and reboot. With the Debian and Ubuntu installation modules, execute
sudo dpkg-reconfigure virtualbox again.
• The kernel disagrees about the version of the gcc used to compile the module.
Make sure that you use the same compiler as used to build the kernel.
Ich komm da nicht weiter.....
Grobian
ich habe mir die aktuelle VB von der Hompage installiert.
Wenn ich VB starte kommt folgende Meldung:
~ # VirtualBox
WARNING: The vboxdrv kernel module is not loaded. Either there is no module
available for the current kernel (2.6.27.7-9-pae) or it failed to
load. Please recompile the kernel module and install it by
sudo /etc/init.d/vboxdrv setup
You will not be able to start VMs until this problem is fixed.
WARNING: The compilation of the vboxdrv.ko kernel module failed during the
installation for some reason. Starting a VM will not be possible.
Please consult the User Manual for build instructions.
/etc/init.d/vboxdrv setup
Wenn ich den Befehl "sudo /etc/init.d/vboxdrv setup" ausführe kommt folgende Meldung:
/etc/init.d/vboxdrv setup
Stopping VirtualBox kernel module done
Recompiling VirtualBox kernel module failed
(Look at /var/log/vbox-install.log to find out what went wrong)
linux-tza2:/home/boss #
Das Programm startet dann schon.
Bei der Installation von Vista kommt dann wieder die obige Meldung "/etc/init.d/vboxdrv setup"
Im Handbuch unter Droublshooting gibt es folgenden Beitrag:
11.5 Linux hosts
11.5.1 Linux kernel module refuses to load
If the VirtualBox kernel module (vboxdrv) refuses to load, i.e. you get an “Error inserting
vboxdrv: Invalid argument”, check (as root) the output of the dmesg command
to find out why the load failed. The most common reasons are:
• With Linux 2.6.19 and higher, the NMI watchdog may be active. Add
nmi_watchdog=0 to the kernel command line (e.g. in your grub configuration)
and reboot. With the Debian and Ubuntu installation modules, execute
sudo dpkg-reconfigure virtualbox again.
• The kernel disagrees about the version of the gcc used to compile the module.
Make sure that you use the same compiler as used to build the kernel.
Ich komm da nicht weiter.....
Grobian