• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

Brother DCP-195C Scanner Problem

W

wschmock

der Drucker des Gerätes funktioniert, nur der Scanner nicht. bei einigen updates geht die Konfiguration verloren, also immer die Treiber und Einstellungen erneuern. auf dem 64-bit Rechner wird der Scanner nicht mehr erkannt, auf dem 32-bit Rechner gibt es bei dmesg folgende Meldung:
Code: 
[  141.024974] usb 3-1: usbfs: interface 0 claimed by usblp while 'brscan-skey-0.2' sets config #1
neuere Treiber gibt es nicht. wer weiß Abhilfe ? ich braucher dringend den Scanner.
 
Nur Interesse halber: Was liefert:
$ sudo dmidecode -s baseboard-product-name beim 64bittigen Rechner?
 
als user:
Code: 
h@k:~> lsusb
Bus 001 Device 004: ID 0bda:5776 Realtek Semiconductor Corp. 
Bus 003 Device 004: ID 04f9:0222 Brother Industries, Ltd 
...
h@k:~> scanimage -L
device `brother3:bus2;dev1' is a Brother DCP-195C USB scanner
h@k:~>
als root:
Code: 
k:~ # scanimage -L
device `brother3:bus2;dev1' is a Brother DCP-195C USB scanner
k:~ #
 
Scanner ist vorhanden, installiere den Treiber einfach noch einmal:
http://support.brother.com/g/b/downloadlist.aspx?c=de&lang=de&prod=dcp195c_all&os=127&flang=English
 
die Treiber sind rpm Pakete. rpm -e ... zum entfernen: ... nicht installiert, rpm -ihv --nodeps ...: Treiber bereits installiert
 
nach dem Einschalten am nächstenTag funktioniert auch der Drucker nicht mehr, Ausgabe von dmesg:
Code: 
[ 2067.030461] usb 3-1: new full-speed USB device number 2 using xhci_hcd
[ 2067.085043] usb 3-1: New USB device found, idVendor=04f9, idProduct=0222
[ 2067.085054] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2067.085060] usb 3-1: Product: DCP-195C
[ 2067.085065] usb 3-1: Manufacturer: Brother
[ 2067.085069] usb 3-1: SerialNumber: BROD3F438843
[ 2067.085351] usb 3-1: ep 0x85 - rounding interval to 512 microframes, ep desc says 800 microframes
[ 2067.189868] usblp 3-1:1.0: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0222
[ 2067.189935] usbcore: registered new interface driver usblp
[ 2067.192012] usb-storage 3-1:1.2: USB Mass Storage device detected
[ 2067.197386] scsi2 : usb-storage 3-1:1.2
[ 2067.198250] usbcore: registered new interface driver usb-storage
[ 2067.677029] usb 3-1: usbfs: interface 0 claimed by usblp while 'brscan-skey-0.2' sets config #1
[ 2068.218949] scsi 2:0:0:0: Direct-Access     Brother  DCP-195C         1.00 PQ: 0 ANSI: 2
[ 2068.219471] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 2068.279022] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 2068.464465] usblp0: removed
[ 2068.573049] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[ 2068.575880] usb 3-1: Device not responding to set address.
[ 2068.778819] usb 3-1: Device not responding to set address.
[ 2068.979655] usb 3-1: device not accepting address 2, error -71
[ 2069.132682] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[ 2069.135851] usb 3-1: Device not responding to set address.
[ 2069.339652] usb 3-1: Device not responding to set address.
[ 2069.540224] usb 3-1: device not accepting address 2, error -71
[ 2069.693368] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[ 2069.696737] usb 3-1: Device not responding to set address.
[ 2069.899692] usb 3-1: Device not responding to set address.
[ 2070.100003] usb 3-1: device not accepting address 2, error -71
[ 2070.253157] usb 3-1: reset full-speed USB device number 2 using xhci_hcd
[ 2070.255434] usb 3-1: Device not responding to set address.
[ 2070.458619] usb 3-1: Device not responding to set address.
[ 2070.659772] usb 3-1: device not accepting address 2, error -71
[ 2070.659917] usb 3-1: USB disconnect, device number 2
[ 2070.665671] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff88008d2e9940
[ 2070.665691] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff88008d2e9980
[ 2070.665701] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff880118a7ec80
[ 2070.665710] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff880118a7ecc0
[ 2070.665719] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff880118a7ed00
[ 2070.665727] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff880117757140
[ 2070.665735] xhci_hcd 0000:00:10.0: xHCI xhci_drop_endpoint called with disabled ep ffff880117757180
[ 2070.772741] usb 3-1: new full-speed USB device number 3 using xhci_hcd
[ 2070.773166] usb 3-1: Device not responding to set address.
[ 2070.974114] usb 3-1: Device not responding to set address.
[ 2071.174428] usb 3-1: device not accepting address 3, error -71
[ 2071.327459] usb 3-1: new full-speed USB device number 4 using xhci_hcd
[ 2071.327826] usb 3-1: Device not responding to set address.
[ 2071.528819] usb 3-1: Device not responding to set address.
[ 2071.729253] usb 3-1: device not accepting address 4, error -71
[ 2071.882154] usb 3-1: new full-speed USB device number 5 using xhci_hcd
[ 2071.882527] usb 3-1: Device not responding to set address.
[ 2072.083518] usb 3-1: Device not responding to set address.
[ 2072.283897] usb 3-1: device not accepting address 5, error -71
[ 2072.436862] usb 3-1: new full-speed USB device number 6 using xhci_hcd
[ 2072.437222] usb 3-1: Device not responding to set address.
[ 2072.638093] usb 3-1: Device not responding to set address.
[ 2072.838539] usb 3-1: device not accepting address 6, error -71
[ 2072.838611] hub 3-0:1.0: unable to enumerate USB device on port 1
yast -> Hardware -> Drucker: Standard ja, Status: Bereit. var > log -> error_log:
Code: 
E [14/Dec/2014:04:31:38 +0100] Unable to bind socket for address 0.0.0.0:631 - Address already in use.
E [14/Dec/2014:04:31:38 +0100] Unable to bind socket for address [v1.::]:631 - Address already in use.
E [14/Dec/2014:04:31:38 +0100] Unable to bind broadcast socket - Address already in use.
E [14/Dec/2014:04:31:40 +0100] [cups-driverd] Bad driver information file "/usr/share/cups/drv/sample.drv"!
E [14/Dec/2014:04:39:42 +0100] Unable to remove /var/run/cups/certs/0!
E [14/Dec/2014:04:40:27 +0100] [cups-driverd] Bad driver information file "/usr/share/cups/drv/sample.drv"!
was nun ?
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Zurück
Oben