Kinternet...Bluetooth Verbindung wird aufgebaut, ciptool ?

[dus-web]

Hallo,

ich habe heute unter Suse 9.0 mein BlueFritz USB zum laufen gebracht. Alles gut und schön. Aber: ICh komm nicht ins Internet. Soll heißen:

Bluetooth Verbindung wird aufgebaut (ciptool show -> 1 00:00...:00 connected). Aber Kinternet kann sich nicht ins Internet einwählen, es beginnt zwar zu wählen bricht aber nach kurzer Zeit immer wieder ab.
Klicke ich auf Verbindung prüfen sagt er mir, das er eine Datei route im Verz. /proc/net nicht öffnen kann und schreibt irgednwas von Standardroute. Und irgendwas mit nem Nameserver.

Vielen Dank für eure Hilfe. Ich weiß echt nicht mehr weiter.

Gruß,

Daniel Ulrich <- der gerade dabei ist komplett auf Linux umzusteigen (auch wenn er das von einem Windoof Rechner asu schreibt [ist nicht meiner])

 

[gaw]

Vielleicht kennt er keinen nameserver. Teste doch einmal was in der /etc/resolv.conf steht nachdem er den Kontakt aufgebaut hat.

mfG
gaw

 

[dus-web]

Die resolv.conf bleibt leer. Gibt es irgendwo eine Logdatei, wo ich die evtl.Fehlermeldungen nachlesen kann?
Irgendwas muss es doch da geben.


Gruß,

Daniel

 

[dus-web]

Nachtrag: gebe ich als root dmesg ein kriege ich folgende Ausgabe (ich poste nur einen Teil der Ausgabe):

BlueZ Core ver 2.3 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded
Network dial timeout is set to 10 sec
CAPI-driver Rev 1.1.4.1: loaded
kcapi: capidrv attached
kcapi: appl 1 up
capidrv: Rev 1.1.4.1: loaded
no channels in open minor(64)
allways open isdnctrl0
no channels in open minor(64)
allways open isdnctrl0
sis900.c: v1.08.06 9/24/2002
eth0: VIA 6103 PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x9800, IRQ 3, 00:0e:a6:83:bb:d0.
eth0: Media Link Off
no channels in open minor(64)
allways open isdnctrl0
raw1394: /dev/raw1394 device initialized
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci_hcd 00:03.3: PCI device 1039:7002 (Silicon Integrated Systems [SiS])
ehci_hcd 00:03.3: irq 9, pci mem e28d9000
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 13:50:22 Sep 24 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-ohci.c: USB OHCI at membase 0xe28db000, IRQ 5
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xe28dd000, IRQ 9
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 3 ports detected
mice: PS/2 mouse device common for all mice
hub.c: new USB device 00:03.0-1, assigned address 2
usb.c: USB device not accepting new address=2 (error=-71)
hub.c: new USB device 00:03.0-1, assigned address 3
usb.c: USB device 3 (vend/prod 0x57c/0x2200) is not claimed by any active driver
.
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
BlueZ HCI USB driver ver 2.4 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
usb.c: registered new driver hci_usb
BlueZ HCI UART driver ver 2.1 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
BlueZ VHCI driver ver 1.1 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
BlueZ L2CAP ver 2.3 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
IPsec Security Association Database (SADB): initialized.
IPsec Security Policy Database (SPD): initialized.
IPsec PF_KEY V2: initialized
IPv6 v0.8 (usagi-cvs/IPsec6 based StS) for NET4.0
IPv6 over IPv4 tunneling driver
ALSA ac97_codec.c:1741: AC'97 0:0 analog subsections not ready
intel8x0: clocking to 48000
kcapi: driver cmtp attached
BlueZ CMTP ver 1.0
Copyright (C) 2002-2003 Marcel Holtmann <marcel@holtmann.org>
BlueFRITZ! USB driver ver 1.1
Copyright (C) 2003 Marcel Holtmann <marcel@holtmann.org>
usb.c: registered new driver bfusb
firmware_class.c:call_helper: firmware: /sbin/hotplug firmware add
remove_proc_entry: bfusb002003/loading busy, count=1
remove_proc_entry: firmware/bfusb002003 busy, count=1
BlueFRITZ! USB loading firmware
de_put: deferred delete of loading
de_put: deferred delete of bfusb002003
BlueFRITZ! USB device ready
capifs: Rev 1.1.4.1
capi20: started up with major 68
kcapi: capi20 attached
capi20: Rev 1.1.4.2: started up with major 68 (middleware+capifs)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
no channels in open minor(64)
allways open isdnctrl0
no channels in open minor(64)
allways open isdnctrl0
lp0: using parport0 (polling).
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux video capture interface: v1.00
eth0: no IPv6 routers present
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
no channels in open minor(64)
allways open isdnctrl0
no channels in open minor(64)
allways open isdnctrl0
no channels in open minor(64)
allways open isdnctrl0
no channels in open minor(64)
allways open isdnctrl0
Found 1 CAPI controller(s) on device 00:04:0E:85:A9:78
kcapi: Controller 1: 00:04:0E:85:A9:78 attached
kcapi: appl 1 down
kcapi: card 1 "00:04:0E:85:A9:78" ready.
kcapi: notify up contr 1
capi: controller 1 up
capidrv: controller 1 up
capidrv-1: now up (2 B channels)
capidrv-1: D2 trace enabled
ippp, open, slot: 0, minor: 0, state: 0000
ippp_ccp: allocated reset data structure cb546000
ippp0: dialing 1 0192658...
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
isdn_net: local hangup ippp0
capidrv-1: chan 0 disconnect request while waiting for CONNECT_CONF
ippp0: Chargesum is 0
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
ippp0: dialing 1 0192658...
capidrv-1: dail ch=0,"0192658,7,0,8610" in use (plci=0x0)
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
isdn_net: local hangup ippp0
capidrv-1: chan 0 disconnect request while waiting for CONNECT_CONF
ippp0: Chargesum is 0
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
ippp_ccp: freeing reset data structure cb546000
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
kcapi: card 1 down.
kcapi: notify down contr 1
capi: controller 1 down
capidrv: controller 1 down
capidrv: bug in free_plci()
capidrv-1: now down.
kcapi: card 1 suspend
kcapi: Controller 1: 00:04:0E:85:A9:78 unregistered
kcapi: capi20 detached
capi: Rev 1.1.4.2: unloaded
kcapi: capidrv detached
capidrv: Rev 1.1.4.1 : unloaded
ISDN-subsystem unloaded
kcapi: driver cmtp detached
CAPI-driver Rev 1.1.4.1 : unloaded
ip6_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 304 bytes per conntrack
CAPI-driver Rev 1.1.4.1: loaded
kcapi: driver cmtp attached
BlueZ CMTP ver 1.0
Copyright (C) 2002-2003 Marcel Holtmann <marcel@holtmann.org>
hci_cmd_task: hci0 command tx timeout
capifs: Rev 1.1.4.1
capi20: started up with major 68
kcapi: capi20 attached
capi20: Rev 1.1.4.2: started up with major 68 (middleware+capifs)
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded
Network dial timeout is set to 10 sec
kcapi: capidrv attached
kcapi: appl 1 up
capidrv: Rev 1.1.4.1: loaded
no channels in open minor(64)
allways open isdnctrl0
Found 1 CAPI controller(s) on device 00:04:0E:85:A9:78
kcapi: Controller 1: 00:04:0E:85:A9:78 attached
kcapi: appl 1 down
kcapi: card 1 "00:04:0E:85:A9:78" ready.
kcapi: notify up contr 1
capidrv: controller 1 up
capidrv-1: now up (2 B channels)
capidrv-1: D2 trace enabled
capi: controller 1 up
ippp, open, slot: 0, minor: 0, state: 0000
ippp_ccp: allocated reset data structure cb4fc800
ippp0: dialing 1 019256191...
isdn_net: local hangup ippp0
capidrv-1: chan 0 disconnect request while waiting for CONNECT_CONF
ippp0: Chargesum is 0
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????
ippp0: dialing 1 019256191...
capidrv-1: dail ch=0,"019256191,7,0,****" in use (plci=0x0)
isdn_net: local hangup ippp0
capidrv-1: chan 0 disconnect request while waiting for CONNECT_CONF
ippp0: Chargesum is 0
capidrv-1: controller dead ??
capidrv-1: listen_change_state state=1 event=1 ????

Vielleicht kann mir damit jemand helfen.

****=Telefonnummer

Danke & Gruß,

Daniel