666pinky666
Newbie
Eigentlich ganz einfach.
Ein Server mit 3 Nics
eth0 für DSL
eth1 fürs interne Netz (Kabel)
eth2 fürs interne Netz (WLAN)
ifconfig -a spuckt folgenden aus:
desweiteren sagt ein route
So weit so gut.
Mein PC auf eth1 mit 192.168.0.6/24 sagt bei einem
ping auf 192.168.0.1 --> OK
ping auf 192.168.1.1 --> OK
ping auf 192.168.1.2 --> nüscht (Das ist der WLAN Acess Point)
ping auf 192.168.1.3 --> auch nix (WIN XP PC)
Der Win XP PC (192.168.1.3/24)
ping auf 192.168.1.2 -- OK
ping auf 192.168.1.1 -- OK
ping auf 192.168.0.1 -- OK
ping auf 192.168.0.6 -- Nix
Woran liegt's ?
Ein Server mit 3 Nics
eth0 für DSL
eth1 fürs interne Netz (Kabel)
eth2 fürs interne Netz (WLAN)
ifconfig -a spuckt folgenden aus:
Code:
eth0 Link encap:Ethernet HWaddr GE:FA:KE:T0:00:00
inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:7dff:fe82:abb2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8851830 errors:425 dropped:0 overruns:0 frame:0
TX packets:9838669 errors:0 dropped:0 overruns:0 carrier:0
collisions:75418 txqueuelen:100
RX bytes:2267192648 (2162.1 Mb) TX bytes:1689955961 (1611.6 Mb)
Interrupt:11 Base address:0xf000
eth1 Link encap:Ethernet HWaddr GE:FA:KE:T0:00:00
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::280:adff:fe30:a4e0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:80703 errors:0 dropped:0 overruns:0 frame:0
TX packets:106665 errors:0 dropped:0 overruns:0 carrier:0
collisions:624 txqueuelen:100
RX bytes:11772596 (11.2 Mb) TX bytes:84997498 (81.0 Mb)
Interrupt:10 Base address:0xc800
eth2 Link encap:Ethernet HWaddr GE:FA:KE:T0:00:00
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::250:baff:fe56:74ed/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:83656 errors:0 dropped:0 overruns:0 frame:0
TX packets:102568 errors:0 dropped:0 overruns:0 carrier:0
collisions:11 txqueuelen:100
RX bytes:10939994 (10.4 Mb) TX bytes:109117669 (104.0 Mb)
Interrupt:9 Base address:0xcc00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3490 errors:0 dropped:0 overruns:0 frame:0
TX packets:3490 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:573045 (559.6 Kb) TX bytes:573045 (559.6 Kb)
ppp0 Link encap:Point-to-Point Protocol
inet addr:80.143.163.24 P-t-P:217.5.98.137 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:8496 errors:0 dropped:0 overruns:0 frame:0
TX packets:13785 errors:0 dropped:3 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:987112 (963.9 Kb) TX bytes:942192 (920.1 Kb)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
desweiteren sagt ein route
Code:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
217.5.98.137 * 255.255.255.255 UH 0 0 0 ppp0
10.0.0.0 * 255.255.255.0 U 0 0 0 eth0
192.168.1.0 * 255.255.255.0 U 0 0 0 eth2
192.168.0.0 * 255.255.255.0 U 0 0 0 eth1
default 217.5.98.137 0.0.0.0 UG 0 0 0 ppp0
So weit so gut.
Mein PC auf eth1 mit 192.168.0.6/24 sagt bei einem
ping auf 192.168.0.1 --> OK
ping auf 192.168.1.1 --> OK
ping auf 192.168.1.2 --> nüscht (Das ist der WLAN Acess Point)
ping auf 192.168.1.3 --> auch nix (WIN XP PC)
Der Win XP PC (192.168.1.3/24)
ping auf 192.168.1.2 -- OK
ping auf 192.168.1.1 -- OK
ping auf 192.168.0.1 -- OK
ping auf 192.168.0.6 -- Nix
Woran liegt's ?