Frankie777
Advanced Hacker
Hallo,
ich habe große Probleme mit einem neuen Rechner. Dieses scheinen mit der Uhrzeit in Verbindung zu stehen.
Ich habe schalte bereits alle paar Stunden den xntp aus, hole die Uhrzeit und schalte dann den xntp wieder an.
Ein großer problem ist immer ein neustart, gestern z.B. mit Failsafe mode gegen 17.44 neu gebootte und danach war der Rechner bis heute vormittag nicht erreichbar. Erst als um 11.00 Uhr ein Cron reboot war kam er wieder ans Netz...
Kann man noch irgendwas verbessert einstellen. Beim shutdown kommt immer die Meldung das die Uhrzeit geschrieben wird, kann man das vielleicht ausschalten?
Bin für jeden Tip dankbar...
hier Auszüge aus den LogFiles:
13 Sep 02:46:44 ntpd[5339]: time correction of 8594 seconds exceeds sanity limit (1000); set clock manually to the correct UTC time.
13 Sep 07:55:10 ntpd[4952]: ntpd exiting on signal 15
-----
Sep 20 17:49:24 kernel: Losing too many ticks!
Sep 20 17:49:24 kernel: TSC cannot be used as a timesource.
Sep 20 17:49:24 kernel: Possible reasons for this are:
Sep 20 17:49:24 kernel: You're running with Speedstep,
Sep 20 17:49:24 kernel: You don't have DMA enabled for your hard disk (see hdparm),
Sep 20 17:49:24 kernel: Incorrect TSC synchronization on an SMP system (see dmesg).
Sep 20 17:49:24 kernel: Falling back to a sane timesource now.
20 Sep 17:43:36 ntpd[5851]: ntpd exiting on signal 15
20 Sep 17:52:35 ntpd[5849]: synchronized to LOCAL(0), stratum 5
20 Sep 17:52:35 ntpd[5849]: kernel time sync disabled 0041
20 Sep 17:53:41 ntpd[5849]: kernel time sync enabled 0001
20 Sep 18:00:01 ntpd[5849]: ntpd exiting on signal 15
20 Sep 18:00:27 ntpd[5875]: parent died before we finished, exiting
21 Sep 11:14:26 ntpd[5768]: synchronized to LOCAL(0), stratum 5
21 Sep 11:14:26 ntpd[5768]: kernel time sync disabled 0041
21 Sep 11:15:30 ntpd[5768]: kernel time sync enabled 0001
ich habe große Probleme mit einem neuen Rechner. Dieses scheinen mit der Uhrzeit in Verbindung zu stehen.
Ich habe schalte bereits alle paar Stunden den xntp aus, hole die Uhrzeit und schalte dann den xntp wieder an.
Ein großer problem ist immer ein neustart, gestern z.B. mit Failsafe mode gegen 17.44 neu gebootte und danach war der Rechner bis heute vormittag nicht erreichbar. Erst als um 11.00 Uhr ein Cron reboot war kam er wieder ans Netz...
Kann man noch irgendwas verbessert einstellen. Beim shutdown kommt immer die Meldung das die Uhrzeit geschrieben wird, kann man das vielleicht ausschalten?
Bin für jeden Tip dankbar...
hier Auszüge aus den LogFiles:
13 Sep 02:46:44 ntpd[5339]: time correction of 8594 seconds exceeds sanity limit (1000); set clock manually to the correct UTC time.
13 Sep 07:55:10 ntpd[4952]: ntpd exiting on signal 15
-----
Sep 20 17:49:24 kernel: Losing too many ticks!
Sep 20 17:49:24 kernel: TSC cannot be used as a timesource.
Sep 20 17:49:24 kernel: Possible reasons for this are:
Sep 20 17:49:24 kernel: You're running with Speedstep,
Sep 20 17:49:24 kernel: You don't have DMA enabled for your hard disk (see hdparm),
Sep 20 17:49:24 kernel: Incorrect TSC synchronization on an SMP system (see dmesg).
Sep 20 17:49:24 kernel: Falling back to a sane timesource now.
20 Sep 17:43:36 ntpd[5851]: ntpd exiting on signal 15
20 Sep 17:52:35 ntpd[5849]: synchronized to LOCAL(0), stratum 5
20 Sep 17:52:35 ntpd[5849]: kernel time sync disabled 0041
20 Sep 17:53:41 ntpd[5849]: kernel time sync enabled 0001
20 Sep 18:00:01 ntpd[5849]: ntpd exiting on signal 15
20 Sep 18:00:27 ntpd[5875]: parent died before we finished, exiting
21 Sep 11:14:26 ntpd[5768]: synchronized to LOCAL(0), stratum 5
21 Sep 11:14:26 ntpd[5768]: kernel time sync disabled 0041
21 Sep 11:15:30 ntpd[5768]: kernel time sync enabled 0001