PrinzEisenherz1
Member
Hi zusammen!
Ich hab ein Dell Inspiron 630m Notebook auf dem ich SUSE 10.3 installiert habe. Hab mein System jetzt mal mit dem Jengelh-Kernel 2.6.23.17-ccj64-default i686 ausgestattet.
Jetzt hab ich aber bei starten des Systems nen Stillstand drin.
Also wenn mein System bootet dann bleibt es für etwa 30sec beim laden
des Pata-Moduls hängen und läuft dann weiter.
Ich hab mal nen Auszug des Startprotokolls hinzugefügt und die entsprechende stelle mit Leerzeilen hervorgehoben!
Hat jemand von euch ne Idee woran das liegen könnte?
Es kommt mir vor wie wenn da irgendwie ein Timeout ne Rolle spielt!
Mfg
Johnny
Ich hab ein Dell Inspiron 630m Notebook auf dem ich SUSE 10.3 installiert habe. Hab mein System jetzt mal mit dem Jengelh-Kernel 2.6.23.17-ccj64-default i686 ausgestattet.
Jetzt hab ich aber bei starten des Systems nen Stillstand drin.
Also wenn mein System bootet dann bleibt es für etwa 30sec beim laden
des Pata-Moduls hängen und läuft dann weiter.
Ich hab mal nen Auszug des Startprotokolls hinzugefügt und die entsprechende stelle mit Leerzeilen hervorgehoben!
Code:
<7>[ 5.332795] ata_piix 0000:00:1f.2: version 2.12
<6>[ 5.332802] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
<6>[ 5.374072] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x180b1, caps: 0xa04713/0x200000
<6>[ 5.383756] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input1
<6>[ 5.489089] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
<7>[ 5.507434] PCI: Setting latency timer of device 0000:00:1f.2 to 64
<6>[ 5.507576] scsi0 : ata_piix
<6>[ 5.514148] scsi1 : ata_piix
<6>[ 5.520651] ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001bfa0 irq 14
<6>[ 5.527371] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001bfa8 irq 15
<4>[ 5.635508] Clocksource tsc unstable (delta = -3868949678 ns)
<6>[ 5.642211] Time: acpi_pm clocksource has been installed.
<6>[ 5.651250] ata1.00: ATA-7: WDC WD1600BEVE-11UYT0, 01.04A01, max UDMA/100
<6>[ 5.657920] ata1.00: 312581808 sectors, multi 8: LBA48
<6>[ 5.664564] ata1.00: applying bridge limits
<6>[ 5.672377] ata1.00: configured for UDMA/100
<6>[ 5.681364] ata2.00: ATAPI: TSSTcorp DVD+/-RW TS-L532B, DE03, max UDMA/33
<6>[ 5.690363] ata2.00: configured for UDMA/33
<5>[ 5.697058] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVE-1 01.0 PQ: 0 ANSI: 5
<5>[ 5.704321] scsi 1:0:0:0: CD-ROM TSSTcorp DVD+-RW TS-L532B DE03 PQ: 0 ANSI: 5
<6>[ 5.725746] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
<6>[ 5.909729] usbcore: registered new interface driver usbfs
<5>[ 5.946317] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
<6>[ 5.953417] usbcore: registered new interface driver hub
<5>[ 5.976610] sd 0:0:0:0: [sda] Write Protect is off
<7>[ 5.983521] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
<6>[ 5.983578] usbcore: registered new device driver usb
Hat jemand von euch ne Idee woran das liegen könnte?
Es kommt mir vor wie wenn da irgendwie ein Timeout ne Rolle spielt!
Mfg
Johnny