• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst]SD Karte wird erkannt, XD Karte nicht

dietterle65

dietterle65

Hallo,

in meinem Kartenleser werden SD Karten sofort erkannt, stecke ich eine XD Karte rein passiert nicht. Nicht einmal die Kontrollleuchte blinkt auf.

Woran kann das liegen?

Kernel: Linux 2.6.34.7-0.7-desktop x86_64
Aktueller Benutzer: thomas@linux-j9go
Distribution: openSUSE 11.3 (x86_64)
KDE: 4.6.00 (4.6.0) "release 381"

Lenovo T61
Prozessor (CPU): Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz

Gruß
amonalex
 
Jetzt kommt die ungeliebte Antwort:

Selbes Gerät. anderes BS, alles ist gut.

Die SD Karte wird sofort gemountet, während bei xd Karte nicht mal die LED aufleuchtet.
Das gibt mir Rätsel auf.

gruß
amonalex
 
Ausgabe von :
Code: 
lspci -vv

und
Code: 
tailf /var/log/messages
beim einstecken der Karte
wären hilfreich.

MfG
misiu
 
Code: 
lspci -vv
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
        Subsystem: Lenovo T61
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information: Len=0a <?>
        Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c) (prog-if 00 [VGA controller])
        Subsystem: Lenovo T61
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 29
        Region 0: Memory at f8100000 (64-bit, non-prefetchable) [size=1M]
        Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
        Region 4: I/O ports at 1800 [size=8]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 41a9
        Capabilities: [d0] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
                Bridge: PM- B3+
        Kernel driver in use: i915

00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 0c)
        Subsystem: Lenovo T61
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Region 0: Memory at f8200000 (64-bit, non-prefetchable) [size=1M]
        Capabilities: [d0] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
                Bridge: PM- B3+

00:19.0 Ethernet controller: Intel Corporation 82566MM Gigabit Network Connection (rev 03)
        Subsystem: Lenovo ThinkPad T61
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 30
        Region 0: Memory at fe000000 (32-bit, non-prefetchable) [size=128K]
        Region 1: Memory at fe025000 (32-bit, non-prefetchable) [size=4K]
        Region 2: I/O ports at 1840 [size=32]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee0100c  Data: 41d1
        Kernel driver in use: e1000e

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Lenovo ThinkPad T61
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 20
        Region 4: I/O ports at 1860 [size=32]
        Kernel driver in use: uhci_hcd

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Lenovo ThinkPad T60
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at 1880 [size=32]
        Kernel driver in use: uhci_hcd

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
        Subsystem: Lenovo ThinkPad T61
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 22
        Region 0: Memory at fe226400 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
        Subsystem: Lenovo ThinkPad T61
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin B routed to IRQ 32
        Region 0: Memory at fe020000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee0100c  Data: 41c1
        Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
                VC1:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=1 ArbSelect=Fixed TC/VC=80
                        Status: NegoPending- InProgress-
        Capabilities: [130 v1] Root Complex Link
                Desc:   PortNumber=0f ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c000
        Kernel driver in use: HDA Intel

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: fc000000-fdffffff
        Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
                        Slot #2, PowerLimit 6.500W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4161
        Capabilities: [90] Subsystem: Lenovo ThinkPad T61
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=01 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: dc000000-df3fffff
        Prefetchable memory behind bridge: 00000000dfe00000-00000000dfefffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
                        Slot #3, PowerLimit 6.500W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4169
        Capabilities: [90] Subsystem: Lenovo ThinkPad T61
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=02 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 03) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 00004000-00004fff
        Memory behind bridge: d8000000-d9ffffff
        Prefetchable memory behind bridge: 00000000dfb00000-00000000dfbfffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
                        Slot #4, PowerLimit 6.500W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4171
        Capabilities: [90] Subsystem: Lenovo ThinkPad T61
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=03 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
        I/O behind bridge: 00005000-00005fff
        Memory behind bridge: d4000000-d5ffffff
        Prefetchable memory behind bridge: 00000000df800000-00000000df8fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
                        Slot #5, PowerLimit 6.500W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4179
        Capabilities: [90] Subsystem: Lenovo ThinkPad T61
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=04 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=0d, subordinate=14, sec-latency=0
        I/O behind bridge: 00006000-00006fff
        Memory behind bridge: d0000000-d1ffffff
        Prefetchable memory behind bridge: 00000000df500000-00000000df5fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
                        Slot #2, PowerLimit 6.500W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4189
        Capabilities: [90] Subsystem: Lenovo ThinkPad T61
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=05 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Lenovo ThinkPad T61
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at 18a0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Lenovo ThinkPad T61
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 4: I/O ports at 18c0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
        Subsystem: Lenovo ThinkPad T61
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at 18e0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
        Subsystem: Lenovo ThinkPad T61
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin D routed to IRQ 19
        Region 0: Memory at fe226800 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
        Capabilities: [58] Debug port: BAR=1 offset=00a0
        Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
        I/O behind bridge: 00007000-0000afff
        Memory behind bridge: f8300000-fbffffff
        Prefetchable memory behind bridge: 00000000f4000000-00000000f7ffffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [50] Subsystem: Lenovo ThinkPad T61

00:1f.0 ISA bridge: Intel Corporation 82801HBM (ICH8M-E) LPC Interface Controller (rev 03)
        Subsystem: Lenovo T61
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.2 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA IDE Controller (rev 03) (prog-if 80 [Master])
        Subsystem: Lenovo Device 20a8
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 16
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at 1c30 [size=16]
        Region 5: I/O ports at 1c20 [size=16]
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ata_piix

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
        Subsystem: Lenovo ThinkPad T61
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 23
        Region 0: Memory at fe226c00 (32-bit, non-prefetchable) [size=256]
        Region 4: I/O ports at 1c40 [size=32]
        Kernel driver in use: i801_smbus

03:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
        Subsystem: Intel Corporation Lenovo ThinkPad T61
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 31
        Region 0: Memory at df3fe000 (64-bit, non-prefetchable) [size=8K]
        Capabilities: [c8] Power Management version 3
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee0300c  Data: 41b9
        Capabilities: [e0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 unlimited
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
                        ClockPM+ Surprise- LLActRep- BwNot-
                LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
        Capabilities: [140 v1] Device Serial Number 00-13-e8-ff-ff-a5-80-d7
        Kernel driver in use: iwlagn

15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
        Subsystem: Lenovo Device 20c6
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 168, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f8300000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
        Memory window 0: f4000000-f7fff000 (prefetchable)
        Memory window 1: c0000000-c3fff000
        I/O window 0: 00007000-000070ff
        I/O window 1: 00007400-000074ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001
        Kernel driver in use: yenta_cardbus

15:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
        Subsystem: Lenovo Device 20c8
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64
        Interrupt: pin C routed to IRQ 18
        Region 0: Memory at f8301000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
        Kernel driver in use: sdhci-pci

15:00.4 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 11)
        Subsystem: Lenovo ThinkPad T61
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin C routed to IRQ 11
        Region 0: Memory at f8301800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME+

15:00.5 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 11)
        Subsystem: Lenovo Device 20cb
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin C routed to IRQ 11
        Region 0: Memory at f8301c00 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME+


Code: 
tailf /var/log/messages                                                                                                                                          
Feb 12 18:57:38 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease                                                                                                            
Feb 12 18:57:58 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 18:57:58 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'                                                                      
Feb 12 18:57:58 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease                                                                                                            
Feb 12 18:58:18 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 18:58:18 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'                                                                      
Feb 12 18:58:18 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease                                                                                                            
Feb 12 18:58:38 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 18:58:38 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 18:58:38 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease                                                                                                            
Feb 12 18:58:58 linux-j9go dhcpcd[5314]: wlan0: timed out                                                                                                                           
Feb 12 18:58:58 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 18:58:58 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 18:59:18 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 18:59:18 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 18:59:18 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 18:59:38 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 18:59:38 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 18:59:38 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 18:59:58 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 18:59:58 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 18:59:58 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 19:00:18 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 19:00:18 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 19:00:18 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 19:00:38 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 19:00:38 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 19:00:38 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 19:00:58 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 19:00:58 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 19:00:58 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
Feb 12 19:01:18 linux-j9go dhcpcd[5314]: wlan0: timed out
Feb 12 19:01:18 linux-j9go dhcpcd[5314]: wlan0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-wlan0.info'
Feb 12 19:01:18 linux-j9go dhcpcd[5314]: wlan0: broadcasting for a lease
 
[falscher Gedankengang]Gibts denn schon einen Treiber für das FileSystem von XD Karten für Linux? Ich denke, da wird der Haken hängen.[/falscher Gedankengang]

Micha :-D

Nachtrag: Ich war Gedanklich bei SDXC-Karten. Also einfach überlesen. Sorry.
 
Das Problem ist bekannt. Für die xD-Karten hält Olympus das Patent und gibt die Beschreibung nicht raus. Daher gibt es keine Möglichkeit xD-Karten unter Linux zu lesen. Das Problem habe ich hier auch. Ich hänge deshalb immer meine Kamera direkt an den PC und lese die dann über USB aus, das geht.
 
Mir hat es auch keine Ruhe gelassen und ich habe mal ein bisschen gelesen (auch wenn es mich selbst nicht betrifft, dank CF ;-) ). Der deutsche Eintrag der Wikipedia gibt nur an, daß die Karte selbst keinen Controller hat, das Endgerät (Kamera oder Rechner) also per Treiber direkt auf die Daten (MLC) zugreifen muss (siehe Beitrag von stka). Die englischen Angaben sind da genauer in Bezug auf Linux:
However, a few models of xD card readers based on the Alauda chip do allow direct access (bypassing the above mechanisms) to an xD card's flash memory; these readers have been reverse-engineered and Linux drivers have been produced by the Alauda Project, which has also documented the on-chip data structures of the xD card. According to this information, the xD card headers are similar to those used by SmartMedia, and include information on the manufacturer of the chip.
Zum Vergrößern anklicken....

Micha :-D
 
Mit den XD-Karten durfte es tatsächlich problematisch sein:
http://lists.debian.org/debian-user-german/2010/04/msg00261.html
 
stka schrieb:
Das Problem ist bekannt. Für die xD-Karten hält Olympus das Patent und gibt die Beschreibung nicht raus. Daher gibt es keine Möglichkeit xD-Karten unter Linux zu lesen. Das Problem habe ich hier auch. Ich hänge deshalb immer meine Kamera direkt an den PC und lese die dann über USB aus, das geht.
Zum Vergrößern anklicken....
:???:
Also hier mit Kartenleser (equip) und XD-Karte (Fujifilm):
Code: 
klapptisch:~ # tailf /var/log/messages 
Feb 12 21:12:21 klapptisch kernel: [ 2036.368607] sd 5:0:0:3: Attached scsi generic sg5 type 0
Feb 12 21:12:21 klapptisch kernel: [ 2036.371960] sd 5:0:0:1: [sdc] Attached SCSI removable disk
Feb 12 21:12:21 klapptisch kernel: [ 2036.374832] sd 5:0:0:2: [sdd] Attached SCSI removable disk
Feb 12 21:12:21 klapptisch kernel: [ 2036.378598] sd 5:0:0:3: [sde] Attached SCSI removable disk
Feb 12 21:12:47 klapptisch kernel: [ 2062.612552] sd 5:0:0:2: [sdd] 32000 512-byte logical blocks: (16.3 MB/15.6 MiB)
Feb 12 21:12:47 klapptisch kernel: [ 2062.613285] sd 5:0:0:2: [sdd] Assuming drive cache: write through
Feb 12 21:12:47 klapptisch kernel: [ 2062.615795] sd 5:0:0:2: [sdd] Assuming drive cache: write through
Feb 12 21:12:47 klapptisch kernel: [ 2062.615804]  sdd: sdd1
Feb 12 21:13:04 klapptisch hald: mounted /dev/sdd1 on behalf of uid 500
Feb 12 21:14:33 klapptisch hald: unmounted /dev/sdd1 from '/media/disk' on behalf of uid 0
Feb 12 21:14:49 klapptisch kernel: [ 2184.612601] sd 5:0:0:2: [sdd] 32000 512-byte logical blocks: (16.3 MB/15.6 MiB)
Feb 12 21:14:49 klapptisch kernel: [ 2184.613493] sd 5:0:0:2: [sdd] Assuming drive cache: write through
Feb 12 21:14:49 klapptisch kernel: [ 2184.616092] sd 5:0:0:2: [sdd] Assuming drive cache: write through
Feb 12 21:14:49 klapptisch kernel: [ 2184.616102]  sdd: sdd1
Feb 12 21:15:05 klapptisch su: (to nobody) root on none
Feb 12 21:15:05 klapptisch su: (to nobody) root on none
Feb 12 21:15:05 klapptisch su: (to nobody) root on none
Feb 12 21:15:10 klapptisch hald: mounted /dev/sdd1 on behalf of uid 500
Code: 
@klapptisch:~> ls /media/disk
DCIM  Janosch & Haindling & Theresa v. Thun  track_06.mp3  track_14.mp3
Code: 
@klapptisch:~> cat /etc/SuSE-*
openSUSE
VERSION = 11.3
openSUSE 11.3 (x86_64)
VERSION = 11.3
Code: 
@klapptisch:~> lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 003: ID 5986:0145 Acer, Inc 
Bus 002 Device 006: ID 07cc:0340 Carry Computer Eng., Co., Ltd 
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 003: ID 1c4f:0003 SiGma Micro 
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Code: 
klapptisch:~ # lsusb -vv -s 002:006

Bus 002 Device 006: ID 07cc:0340 Carry Computer Eng., Co., Ltd 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x07cc Carry Computer Eng., Co., Ltd
  idProduct          0x0340 
  bcdDevice            0.05
  iManufacturer           1         Ltd
  iProduct                2 Winter Ver1.3   
  iSerial                 3 401285326702
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              4 1.06.30.0704
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)
 
Moin,

ich gebe den Beitrag als gelöst ein.
Hänge ich die xd Karte mit Fotoapperat ein ist alles gut.

Danke und schönen Sonntag

Gruß
amonalex
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Zurück
Oben