Hallo,
da ja nun bald meine 9.3 veraltet ist wollte ich am WE 10.2 parallel installieren.
Nach viel Hin und her mit Neuinstallationen (nun weiß ich warum, s.u.) hab ich jetzt folgenden Stand:
Soweit die Dateien, aus Suse 9.3 sowie die fstab aus der 10.2 herausgeholt.
Mit der Einstellung bootet die SuSE 9.3, aber die 10.2 nicht. Es bleibt hängen bei "Waiting on /dev/sda7..." Ich habe nun herausgefunden, daß beim Booten die Reihenfolge vertauscht wird. Plötzlich ist
Also einmal durchgetauscht.
Woran kann das liegen? Beim Booten über die CD gehts (statt Reparatur einfach installiertes System booten und sda7 gewählt): Eine Reparatur zeigt nichts aufälliges und ist schon mehrfach gelaufen.
Was kan nich tun, damit die Reichenfolge bleibt wie gewünscht und Susi damit die richtige / findet?
Ach ja, beide Systeme greifen auf die gleiche Partition /boot zu, wie aus der menu.lst zu ersehen.
Ach ja, die beiden ungenutzetn Platten sind meine Soft-RAID-Platten. einegdlich sollte das neue System darauf, aber ich dachte, es liegt am RAID. Nun ist das System halt auf dem RAID5 War auch noch Platz ...
Grüße
Carsten
da ja nun bald meine 9.3 veraltet ist wollte ich am WE 10.2 parallel installieren.
Nach viel Hin und her mit Neuinstallationen (nun weiß ich warum, s.u.) hab ich jetzt folgenden Stand:
Code:
main:/boot/grub # cat /boot/grub/menu.lst
# Modified by YaST2. Last modification on Mo Apr 23 02:27:15 CEST 2007
default 0
timeout 8
gfxmenu (hd0,6)/message
###Don't change this comment - YaST2 identifier: Original name: linux###
title openSUSE 10.2
root (hd0,6)
kernel /vmlinuz root=/dev/sda7 vga=0x31a resume=/dev/hda1 splash=silent showopts
initrd /initrd
###Don't change this comment - YaST2 identifier: Original name: linux###
title SuSE93
root (hd0,6)
kernel /vmlinuz-2.6.11.4-21.15-default root=/dev/sda2 vga=0x31a resume=/dev/hda1 splash=silent showopts
initrd /initrd-2.6.11.4-21.15-default
###Don't change this comment - YaST2 identifier: Original name: floppy###
title Diskette
rootnoverify (hd0,0)
chainloader (fd0)+1
###Don't change this comment - YaST2 identifier: Original name: failsafe###
title Failsafe -- openSUSE 10.2
root (hd0,6)
kernel /vmlinuz root=/dev/sda7 vga=normal showopts ide=nodma apm=off acpi=off noresume nosmp noapic maxcpus=0 edd=off 3
initrd /initrd
title Kernel-2.6.18.8-0.1-default
root (hd0,6)
kernel /vmlinuz-2.6.18.8-0.1-default root=/dev/sda7 vga=0x31a resume=/dev/hda1 splash=silent showopts
initrd /initrd-2.6.18.8-0.1-default
main:/boot/grub #
Code:
main:/boot/grub # fdisk -l
Disk /dev/sda: 499.9 GB, 499977814016 bytes
255 heads, 63 sectors/track, 60785 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 131 1052226 82 Linux swap / Solaris
/dev/sda2 * 132 4310 33564882 83 Linux
/dev/sda3 4311 60781 453603307+ f W95 Ext'd (LBA)
/dev/sda5 4311 6921 20972826 83 Linux
/dev/sda6 6922 22586 125829081 83 Linux
/dev/sda7 22587 25197 20972826 83 Linux
Disk /dev/sdb: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
Disk /dev/sdc: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
Disk /dev/hda: 40.0 GB, 40020664320 bytes
255 heads, 63 sectors/track, 4865 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 131 1052226 82 Linux swap / Solaris
/dev/hda2 * 132 2742 20972857+ f W95 Ext'd (LBA)
/dev/hda3 2743 4865 17052997+ 83 Linux
/dev/hda5 132 655 4208998+ 83 Linux
/dev/hda6 656 2211 12496582 83 Linux
/dev/hda7 2212 2742 4265226 83 Linux
main:/boot/grub #
Code:
main:/boot/grub # cat device.map
(fd0) /dev/fd0
(hd1) /dev/sda
(hd3) /dev/sdc
(hd2) /dev/sdb
(hd0) /dev/hda
Code:
main:/boot/grub # cat /etc/fstab (SuSE 9.3)
/dev/sda2 / reiserfs acl,user_xattr 1 1
/dev/hda3 /Backup ext3 defaults 1 2
# /dev/md1 /Musik ext3 defaults 1 2
/dev/hda7 /boot ext2 acl,user_xattr 1 2
/dev/hda6 /Backup1 ext3 acl,user_xattr 1 2
# /dev/md0 /mnt/md0 ext3 defaults 1 2
/dev/hda5 /var/lib/YaST2/you ext3 defaults 1 2
/dev/hda1 swap swap pri=42 0 0
/dev/sda1 swap swap pri=42 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
proc /proc proc defaults 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
sysfs /sys sysfs noauto 0 0
/dev/fd0 /media/floppy subfs noauto,fs=floppyfss,procuid,nodev,nosuid,sync 0 0
/dev/sda5 /Ablage ext3 acl,user_xattr 1 2
/dev/dvdrecorder /media/dvdrecorder subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=utf8 0 0
/dev/dvd /media/dvd subfs noauto,fs=cdfss,ro,procuid,nosuid,nodev,exec,iocharset=utf8 0 0
/dev/sda6 /Musik ext3 acl,user_xattr 1 2
/dev/sda7 /mnt/Suse102 ext3 acl,user_xattr 1 2
#/dev/md0 /mnt/md0_10.2 ext3 defaults 1 2
#/dev/md1 /mnt/md1_var ext3 defaults 1 2
#/dev/md2 /mnt/md2 ext3 defaults 1 2
Code:
main:/boot/grub # cat /mnt/Suse102/etc/fstab
/dev/sda7 / ext3 acl,user_xattr 1 1
/dev/sda5 /Ablage ext3 defaults 1 2
/dev/hda3 /Backup ext3 defaults 1 2
/dev/hda6 /Backup1 ext3 defaults 1 2
/dev/sda6 /Musik ext3 defaults 1 2
/dev/hda7 /boot ext2 defaults 1 2
/dev/sda2 /mnt/Suse93 reiserfs defaults 1 2
/dev/hda5 /mnt/hda5 ext3 defaults 1 2
/dev/hda1 swap swap defaults 0 0
/dev/sda1 swap swap defaults 0 0
proc /proc proc defaults 0 0
sysfs /sys sysfs noauto 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
devpts /dev/pts devpts mode=0620,gid=5 0 0
/dev/fd0 /media/floppy auto noauto,user,sync 0 0
Mit der Einstellung bootet die SuSE 9.3, aber die 10.2 nicht. Es bleibt hängen bei "Waiting on /dev/sda7..." Ich habe nun herausgefunden, daß beim Booten die Reihenfolge vertauscht wird. Plötzlich ist
Code:
sda -> sdc
sdb -> sda
sdc -> sdb
Woran kann das liegen? Beim Booten über die CD gehts (statt Reparatur einfach installiertes System booten und sda7 gewählt): Eine Reparatur zeigt nichts aufälliges und ist schon mehrfach gelaufen.
Was kan nich tun, damit die Reichenfolge bleibt wie gewünscht und Susi damit die richtige / findet?
Ach ja, beide Systeme greifen auf die gleiche Partition /boot zu, wie aus der menu.lst zu ersehen.
Ach ja, die beiden ungenutzetn Platten sind meine Soft-RAID-Platten. einegdlich sollte das neue System darauf, aber ich dachte, es liegt am RAID. Nun ist das System halt auf dem RAID5 War auch noch Platz ...
Grüße
Carsten