Intel Pro/Wireless Install Problem

[Freecoffee]

Und zwar nach dem Laden des Moduls mittels modprobe.

 

[D4rKMaN]

SirTuxus:~ # modprobe -v ipw3945
install /sbin/modprobe --ignore-install ipw3945 ; sleep 0.5 ; /sbin/ipw3945d --quiet
insmod /lib/modules/2.6.16.21-0.25-smp/weak-updates/ipw3945.ko
FATAL: Error inserting ipw3945 (/lib/modules/2.6.16.21-0.25-smp/weak-updates/ipw3945.ko): Unknown symbol in module, or unknown parameter (see dmesg)
2006-10-25 11:31:35: ERROR: Could not find Intel PRO/Wireless 3945ABG Network Connection
SirTuxus:~ # dmesg
Linux version 2.6.16.21-0.25-smp (geeko@buildhost) (gcc version 4.1.0 (SUSE Linux)) #1 SMP Tue Sep 19 07:26:15 UTC 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable)
 BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data)
 BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 262096
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 32720 pages, LIFO batch:7
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 ACPIAM                                ) @ 0x000f79d0
ACPI: RSDT (v001 A M I  OEMRSDT  0x06000607 MSFT 0x00000097) @ 0x3ffd0000
ACPI: FADT (v002 A M I  OEMFACP  0x06000607 MSFT 0x00000097) @ 0x3ffd0200
ACPI: MADT (v001 A M I  OEMAPIC  0x06000607 MSFT 0x00000097) @ 0x3ffd0390
ACPI: MCFG (v001 A M I  OEMMCFG  0x06000607 MSFT 0x00000097) @ 0x3ffd03f0
ACPI: BOOT (v001 A M I  OEMBOOT  0x06000607 MSFT 0x00000097) @ 0x3ffd0430
ACPI: OEMB (v001 A M I  AMI_OEM  0x06000607 MSFT 0x00000097) @ 0x3ffde040
ACPI: DSDT (v001  A6J00 A6J00005 0x00000005 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
Overriding APIC driver with bigsmp
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Physflat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bee00000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 vga=0x314    resume=/dev/hda1  splash=silent
bootsplash: silent mode.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1662.897 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032368k/1048384k available (1611k kernel code, 15352k reserved, 731k data, 188k init, 130880k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3332.13 BogoMIPS (lpj=6664264)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 2336k freed
 not found!
CPU0: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
Leaving ESR disabled.
Enabling SMP...
Booting processor 1/1 eip 3000
Initializing CPU#1
Leaving ESR disabled.
Calibrating delay using timer specific routine.. 3325.24 BogoMIPS (lpj=6650480)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000140 0000c1a9 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
Total of 2 processors activated (6657.37 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Enabling SMP...
Brought up 2 CPUs
migration_cost=25
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
PCI: BIOS Bug: MCFG area is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #05 (-#08) is hidden behind transparent bridge #04 (-#05) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 *7 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 7 12)
ACPI: Power Resource [GFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
Setting up standard PCI resources
pnp: 00:0a: ioport range 0x400-0x41f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: 9000-bfff
  MEM window: fdf00000-fdffffff
  PREFETCH window: bdf00000-ddefffff
PCI: Bridge: 0000:00:1c.0
  IO window: c000-cfff
  MEM window: fe000000-fe0fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
  IO window: disabled.
  MEM window: fe100000-fe1fffff
  PREFETCH window: disabled.
PCI: Bus 5, cardbus bridge: 0000:04:01.0
  IO window: 0000d000-0000d0ff
  IO window: 0000d400-0000d4ff
  PREFETCH window: 50000000-51ffffff
  MEM window: 52000000-53ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: fe200000-feafffff
  PREFETCH window: ddf00000-dfefffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.3 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 193
Simple Boot Flag at 0x52 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1161773810.780:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.3:pcie00]
Allocate Port Service[0000:00:1c.3:pcie02]
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 3750k, total 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:ab68
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 50686 bytes,<6>...found (800x600, 28094 bytes, v3).
Console: switching to colour frame buffer device 96x33
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
ACPI wakeup devices:
P0P2 P0P1 CBS0 P394 USB0 USB1 EUSB MC97 P0P4 P0P5 P0P6 P0P7 P0P8 P0P9 HDAC SLPB
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 188k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 233
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HTS541080G9AT00, ATA DISK drive
hdb: MATSHITADVD-RAM UJ-841S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (32 C)
ACPI: Fan [FN00] (off)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Attempting manual resume
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
reiserfs: using flush barriers
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
Adding 2104472k swap on /dev/hda1.  Priority:-1 extents:1 across:2104472k
ieee1394: Initialized config rom entry `ip1394'
ieee80211_crypt: module not supported by Novell, setting U taint flag.
ieee80211_crypt: registered algorithm 'NULL'
ACPI: PCI Interrupt 0000:04:01.1[B] -> GSI 18 (level, low) -> IRQ 233
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[233]  MMIO=[feaff800-feafffff]  Max Packet=[2048]  IR/IT contexts=[4/4]
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 50, io base 0x0000ec00
ieee80211: module not supported by Novell, setting U taint flag.
ieee80211: 802.11 data/management/control stack, 1.2.15
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.16.21-0.25-smp uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ipw3945: module not supported by Novell, setting U taint flag.
ipw3945: disagrees about version of symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: disagrees about version of symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: disagrees about version of symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: disagrees about version of symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: disagrees about version of symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: disagrees about version of symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: disagrees about version of symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: disagrees about version of symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: disagrees about version of symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_rx
ipw3945: disagrees about version of symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: disagrees about version of symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: disagrees about version of symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: disagrees about version of symbol ieee80211_get_geo
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: disagrees about version of symbol free_ieee80211
ipw3945: Unknown symbol free_ieee80211
ipw3945: disagrees about version of symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: disagrees about version of symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: disagrees about version of symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: disagrees about version of symbol alloc_ieee80211
ipw3945: Unknown symbol alloc_ieee80211
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000e880
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.16.21-0.25-smp uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 58, io base 0x0000e800
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.16.21-0.25-smp uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 18 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 233, io base 0x0000e480
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb usb4: Manufacturer: Linux 2.6.16.21-0.25-smp uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
usb usb4: configuration #1 chosen from 1 choice
i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
usb 1-1: new device found, idVendor=046d, idProduct=c01e
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
usb 1-1: configuration #1 chosen from 1 choice
ehci_hcd 0000:00:1d.7: irq 50, io mem 0xfebfbc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.16.21-0.25-smp ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
agpgart: Detected an Intel 945GM Chipset.
agpgart: AGP aperture is 256M @ 0x0
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e018000349c67a]
usb 5-7: new high speed USB device using ehci_hcd and address 4
usb 5-7: new device found, idVendor=0402, idProduct=5602
usb 5-7: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 5-7: Product: USB2.0 Camera
usb 5-7: configuration #1 chosen from 1 choice
usb 1-1: USB disconnect, address 2
usbcore: registered new driver hiddev
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1b.0 to 64
usb 1-1: new low speed USB device using uhci_hcd and address 3
usb 1-1: new device found, idVendor=046d, idProduct=c01e
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
usb 1-1: configuration #1 chosen from 1 choice
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: new device found, idVendor=0b05, idProduct=1712
usb 3-2: new device strings: Mfr=0, Product=0, SerialNumber=3
usb 3-2: SerialNumber: 0194E8-5B-0002
usb 3-2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 193
Yenta: CardBus bridge found at 0000:04:01.0 [1043:1237]
input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new driver hci_usb
Yenta: ISA IRQ mask 0x08a8, PCI irq 193
Socket status: 30000820
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xdfff
cs: IO port probe 0xd000-0xdfff: clean.
pcmcia: parent PCI bridge Memory window: 0xfe200000 - 0xfeafffff
pcmcia: parent PCI bridge Memory window: 0xddf00000 - 0xdfefffff
hw_random: RNG not detected
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
pccard: CardBus card inserted into slot 0
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x4bf 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: excluding 0x830-0x87f
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Enabling device 0000:05:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 17 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:05:00.0 to 64
ohci_hcd 0000:05:00.0: OHCI Host Controller
ohci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 6
ohci_hcd 0000:05:00.0: irq 193, io mem 0x52000000
usb usb6: new device found, idVendor=0000, idProduct=0000
usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.16.21-0.25-smp ohci_hcd
usb usb6: SerialNumber: 0000:05:00.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
PCI: Enabling device 0000:05:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:00.1[B] -> GSI 17 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:05:00.1 to 64
ohci_hcd 0000:05:00.1: OHCI Host Controller
ohci_hcd 0000:05:00.1: new USB bus registered, assigned bus number 7
ohci_hcd 0000:05:00.1: irq 193, io mem 0x52001000
usb usb7: new device found, idVendor=0000, idProduct=0000
usb usb7: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: OHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.16.21-0.25-smp ohci_hcd
usb usb7: SerialNumber: 0000:05:00.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
dm-netlink version 0.0.2 loaded
usb 7-1: new full speed USB device using ohci_hcd and address 2
usb 7-1: new device found, idVendor=0af0, idProduct=6300
usb 7-1: new device strings: Mfr=1, Product=2, SerialNumber=4
usb 7-1: Product: Fusion UMTS Quad-GPRS
usb 7-1: Manufacturer: Option N.V.
usb 7-1: SerialNumber: ?Serial Numbe
usb 7-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Option 3G data card
option 7-1:1.0: Option 3G data card converter detected
usb 7-1: Option 3G data card converter now attached to ttyUSB0
option 7-1:1.1: Option 3G data card converter detected
usb 7-1: Option 3G data card converter now attached to ttyUSB1
option 7-1:1.2: Option 3G data card converter detected
usb 7-1: Option 3G data card converter now attached to ttyUSB2
option 7-1:1.3: Option 3G data card converter detected
usb 7-1: Option 3G data card converter now attached to ttyUSB3
usbcore: registered new driver option
drivers/usb/serial/option.c: Option Card (PC-Card to) USB to Serial Driver: v0.4
loop: loaded (max 8 devices)
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
reiserfs: using flush barriers
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
AppArmor: AppArmor (version 2.0-19.43r6320) initialized
audit(1161773837.125:2): AppArmor (version 2.0-19.43r6320) initialized

NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8190 buckets, 65520 max) - 232 bytes per conntrack
ACPI: AC Adapter [AC0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
IA-32 Microcode Update Driver v1.14 unregistered
audit(1161766646.632:3): audit_backlog_limit=256 old=64 by auid=4294967295
bootsplash: status on console 0 changed to on
fglrx: module not supported by Novell, setting U taint flag.
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 928 MBytes.
[fglrx] module loaded - fglrx 8.29.6 [Sep 19 2006] on minor 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
[fglrx] total      GART = 134217728
[fglrx] free       GART = 118226944
[fglrx] max single GART = 118226944
[fglrx] total      LFB  = 258011136
[fglrx] free       LFB  = 241627136
[fglrx] max single LFB  = 241627136
[fglrx] total      Inv  = 0
[fglrx] free       Inv  = 0
[fglrx] max single Inv  = 0
[fglrx] total      TIM  = 0
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1b.0 to 64
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
ppp0 renamed to modem0
PPP BSD Compression module registered
PPP Deflate Compression module registered
SFW2-INext-DROP-DEFLT-INV IN=modem0 OUT= MAC= SRC=64.233.169.99 DST=10.129.143.62 LEN=40 TOS=0x00 PREC=0x00 TTL=43 ID=8821 PROTO=TCP SPT=80 DPT=18565 WINDOW=6951 RES=0x00 ACK URGP=0
SFW2-OUT-ERROR IN= OUT=modem0 SRC=10.129.143.62 DST=64.12.164.120 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=34915 DF PROTO=TCP SPT=23284 DPT=80 WINDOW=1728 RES=0x00 ACK PSH FIN URGP=0 OPT (0101080A0002E0080084CF02)
SFW2-OUT-ERROR IN= OUT=modem0 SRC=10.129.143.62 DST=64.12.164.120 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=34916 DF PROTO=TCP SPT=23284 DPT=80 WINDOW=1728 RES=0x00 ACK PSH FIN URGP=0 OPT (0101080A00033C680084CF02)
ipw3945: module not supported by Novell, setting U taint flag.
ipw3945: disagrees about version of symbol ieee80211_wx_get_encodeext
ipw3945: Unknown symbol ieee80211_wx_get_encodeext
ipw3945: disagrees about version of symbol ieee80211_wx_set_encode
ipw3945: Unknown symbol ieee80211_wx_set_encode
ipw3945: disagrees about version of symbol ieee80211_wx_get_encode
ipw3945: Unknown symbol ieee80211_wx_get_encode
ipw3945: disagrees about version of symbol ieee80211_txb_free
ipw3945: Unknown symbol ieee80211_txb_free
ipw3945: disagrees about version of symbol ieee80211_wx_set_encodeext
ipw3945: Unknown symbol ieee80211_wx_set_encodeext
ipw3945: disagrees about version of symbol ieee80211_wx_get_scan
ipw3945: Unknown symbol ieee80211_wx_get_scan
ipw3945: disagrees about version of symbol ieee80211_freq_to_channel
ipw3945: Unknown symbol ieee80211_freq_to_channel
ipw3945: disagrees about version of symbol ieee80211_set_geo
ipw3945: Unknown symbol ieee80211_set_geo
ipw3945: disagrees about version of symbol ieee80211_rx
ipw3945: Unknown symbol ieee80211_rx
ipw3945: disagrees about version of symbol ieee80211_get_channel
ipw3945: Unknown symbol ieee80211_get_channel
ipw3945: disagrees about version of symbol ieee80211_channel_to_index
ipw3945: Unknown symbol ieee80211_channel_to_index
ipw3945: disagrees about version of symbol ieee80211_rx_mgt
ipw3945: Unknown symbol ieee80211_rx_mgt
ipw3945: disagrees about version of symbol ieee80211_get_geo
ipw3945: Unknown symbol ieee80211_get_geo
ipw3945: disagrees about version of symbol free_ieee80211
ipw3945: Unknown symbol free_ieee80211
ipw3945: disagrees about version of symbol ieee80211_tx_frame
ipw3945: Unknown symbol ieee80211_tx_frame
ipw3945: disagrees about version of symbol ieee80211_is_valid_channel
ipw3945: Unknown symbol ieee80211_is_valid_channel
ipw3945: disagrees about version of symbol ieee80211_get_channel_flags
ipw3945: Unknown symbol ieee80211_get_channel_flags
ipw3945: disagrees about version of symbol alloc_ieee80211
ipw3945: Unknown symbol alloc_ieee80211

 

[Freecoffee]

Irgendetwas ist da bei der ieee80211-Installation schief gelaufen, oder da ist ein Bug. Frag mal bei den Entwicklern nach oder schau ins Archiv der Mailingliste auf ieee80211.sf.net.

 

[oleg]

also zu diesen Fehlermeldungen fällt mir auch nichts ein, aber das hilft Dir vermutlich nicht gerade ...

vielleicht versuchst Du mal Deine ganzen Installationen rückgängig zu machen - ich glaube im 80211-Archiv ist auch ein uninstall-Script dabei ...

Es funktioniert nämlich definitiv bei SuSE 10.1 von Hause aus nach Installation der Firmware per yast.

Aber vielleicht hat ja jemand anderes eine Idee.

 

[D4rKMaN]

Irgendetwas ist da bei der ieee80211-Installation schief gelaufen, oder da ist ein Bug. Frag mal bei den Entwicklern nach oder schau ins Archiv der Mailingliste auf ieee80211.sf.net.

Versuche einfach das geringfühgig ältere packet.

mal sehen od es dann geht

Edit:
Nein geht nicht immernoch das selbe. ich kann die karte auch im yast nicht entfernen.
Und mal neu einfügen. Aber geht ja leider nicht.

 

[Freecoffee]

Vielleicht gibt es da irgendwo noch ein altes Modul.
Mach mal als root folgendes in der Konsole:

for i in ieee80211 ipw3945; do \
find /lib/modules/`uname -r` -iname ${i}*; done

Das sollte alle Dateien im Modulpfad anzeigen, die irgendwie nach ieee80211 oder ipw3945 aussehen. Du kannst auch gerne mit KDE o.ä. danach suchen in /lib/modules/<kernelversion>/. Hauptsache, du beseitigst alle gefundenen Dateien.

Anschließend noch eine Installation.

 

[D4rKMaN]

Ich hab nochmal gesucht und habe folgendes gefunden.

Fix problem with 0.0.74 and newer with building on some systems.

If you experience build or module loading problems with the ipw3945 driver
related to ieee80211 symbols, try this patch and see if it solves the issue.

Signed-off-by: James Ketrenos <jketreno@linux.intel.com>

diff --git a/Makefile b/Makefile
index 6fc7645..1cbcdca 100644
--- a/Makefile
+++ b/Makefile
@@ -179,7 +179,7 @@ distclean: clean
rm -f tags TAGS

modules:
- $(MAKE) -C $(KSRC) M=$(PWD) modules
+ $(MAKE) -C $(KSRC) M=$(PWD) MODVERDIR=$(IEEE80211_MODVERDIR) modules

add_radiotap:
@snapshot/add_radiotap $(KSRC)

Da steht ja das es mit manchen Probleme gibt und man soll den Patch probieren.
Muss ich den selber machen?

Kann damit so nichts anfangen, wie mach ich das?

Sry für die nicht wissenheit aber es muss doch gehen....

 

[Freecoffee]

Musst du selbst machen.
Dazu wechselst du in das Verzeichnis des Treibers, öffnest die Datei Makefile und ersetzt die Zeile 182 durch folgende

$(MAKE) -C $(KSRC) M=$(PWD) MODVERDIR=$(IEEE80211_MODVERDIR) modules

Übrigens: Es wäre nett, wenn du dir die Benutzung der Editier-Funktion angewöhnen könntest, dann muss ich das nicht immer machen.