keine Verbindung zum Router

[Elektrofreak]

Hi

ich benutze erst seid gestern Suse Linux 10.1 und habe kaum erfahrung mit Linux.

Nun versuche ich über WLAN ins Internet zu kommen, jedoch funktioniert es nicht.

Der Stick wurde erkannt und die Treiber sind installiert (Treiber liefen in "Taskmanager", k.a. den Linux-Namen), in YaST kann ich den Stick konfigurieren aber kein Prog kann auf den Stick zufreifen, um eine Verbindung zum Router herzustellen. Des weiteren leuchtet die LED des Sticks überhaupt nicht geschweige denn blinkt, was sie sogar normalerweise macht, wenn der Stick nur an ist und nichts macht (unter Win).


Weitere wichtige Informationen:

- Der Stick ist ein ZyAir B-220; über USB angeschlossen
- Der Chip ist ein ZyDas

hier ein paar Screenshots:

 

[Freecoffee]

Was liefert lsmod?
Hast du hier schon einmal vorbeigeschaut?

 

[Anonymous]

Hallo,

4 Fragen:

1. Wer/was sind eth0 und eth1? (ich tippe mal auf 2 eingebaute LAN-Karten, richtig?)

2. Hast Du mit aktivierter eth0 (denn das sieht man aus einem der Screenshots) versucht per WLAN ins Netz zu kommen?

3. (optional) Wenn die Antwort auf 2 "Ja" lauten sollte, dann: Woher soll Dein System dann wissen, über welches Interface der Netzwerkverkehr gehen soll?

4. (ebenfalls optional) Wieso haben eigentlich eth0 und eth1 die SELBE IP-Adresse?

Greetz,

RM

 

[Elektrofreak]

lsmod kam folgendes raus:

matsmarcus@Mats-Marcus:~> lsmod
Module Size Used by
zd1201 22660 0
firmware_class 11648 1 zd1201
ipv6 252000 22
snd_pcm_oss 49024 0
snd_mixer_oss 18304 1 snd_pcm_oss
snd_seq 55712 0
snd_seq_device 9360 1 snd_seq
edd 10504 0
button 7968 0
battery 11016 0
ac 5896 0
apparmor 53540 0
aamatch_pcre 14464 1 apparmor
nls_utf8 2432 1
ntfs 185320 1
loop 16016 0
usbhid 43296 0
dm_mod 59976 0
nvidia 5428980 12
floppy 65224 0
sk98lin 142816 0
ohci_hcd 19460 0
forcedeth 23684 0
ide_cd 40480 0
cdrom 36008 1 ide_cd
ehci_hcd 30216 0
usbcore 130600 5 zd1201,usbhid,ohci_hcd,ehci_hcd
ohci1394 32584 0
ieee1394 101624 1 ohci1394
i2c_nforce2 7680 0
snd_intel8x0 35624 1
snd_ac97_codec 102232 1 snd_intel8x0
snd_ac97_bus 2816 1 snd_ac97_codec
snd_pcm 97292 3 snd_pcm_oss,snd_intel8x0,snd_ac97_codec
snd_timer 24968 2 snd_seq,snd_pcm
snd 65192 10 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 10656 1 snd
snd_page_alloc 10640 2 snd_intel8x0,snd_pcm
i2c_core 23576 2 nvidia,i2c_nforce2
parport_pc 39656 1
lp 13192 0
parport 39180 2 parport_pc,lp
reiserfs 222464 2
fan 5640 0
thermal 15888 0
processor 26068 1 thermal
sg 35240 0
sata_nv 10628 4
libata 74136 1 sata_nv
amd74xx 15024 0 [permanent]
sd_mod 17688 5
scsi_mod 145328 3 sg,libata,sd_mod
ide_disk 16512 0
ide_core 145380 3 ide_cd,amd74xx,ide_disk
matsmarcus@Mats-Marcus:~>

ich habe 2 LAN-Karten im rechner, genau. Momentan gehe ich über eine von beiden (k.a. welche) über meinen laptop, welcher als proxy konfiguriert ist ins internet (über WLAN)

desshalb habe ich beiden LAN-Karten auch die gleiche IP gegeben, etwas schwachsinnig,, gebe ich zu aber das ist jetzt ja nunmal egal.

Ich gehe einfach mal davon aus (wenns anders ist, bitte "NEIN" rufen ;-) ), dass der WLAN-Stick irgendwie nicht richtig eingerichtet ist, da es nirgendwo das Gerät wlan0 gibt, nur eth (also LAN) und lo (loopback oder sowas wie localhost?)

Und woher das system wissen soll, worüber es ins inet soll, habe ich leine ahnung *gg*.


Nebenbei: Die LED des Sticks leuchtet überhaupt nicht -> wie bei Win wenn das Gerät deaktiviert ist.



Vielen Dank für eure Antworten



Edit:

wenn jemand möchte (und ich ihm auch vertrauen kann, gebe ich eine Remote-verbindung frei (VNC). Dann kann die Person sich selber überlegen, wo das Problem sein könnte. Ich fänds echt nett ;-)

 

[Freecoffee]

Mach einmal folgendes:

sudo /sbin/rmmod zd1201
sudo dmesg -c
sudo /sbin/modprobe zd1201

und poste danach die Ausgabe von dmesg.

 

[Elektrofreak]

sieht nach nicht installierter firmware aus:

matsmarcus@mats-marcus:~$ sudo /sbin/rmmod zd1201
matsmarcus@mats-marcus:~$ sudo dmesg -c
[ 0.000000] Bootdata ok (command line is root=/dev/sda1 ro quiet splash)
[ 0.000000] Linux version 2.6.15-25-amd64-generic (buildd@king) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Wed Jun 14 11:28:03 UTC 2006
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[ 0.000000] BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7dc0
[ 0.000000] ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff3040
[ 0.000000] ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff30c0
[ 0.000000] ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x000000003fff98c0
[ 0.000000] ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff99c0
[ 0.000000] ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff9800
[ 0.000000] ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
[ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0
[ 0.000000] SRAT: Node 0 PXM 0 0-a0000
[ 0.000000] SRAT: Node 0 PXM 0 0-40000000
[ 0.000000] Using 63 for the hash shift.
[ 0.000000] Bootmem setup node 0 0000000000000000-000000003fff0000
[ 0.000000] On node 0 totalpages: 257522
[ 0.000000] DMA zone: 3017 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 254505 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages, LIFO batch:0
[ 0.000000] HighMem zone: 0 pages, LIFO batch:0
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:15 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Setting APIC routing to physical flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Checking aperture...
[ 0.000000] CPU 0: aperture @ 300000000 size 32 MB
[ 0.000000] Aperture from northbridge cpu 0 too small (32 MB)
[ 0.000000] No AGP bridge found
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: root=/dev/sda1 ro quiet splash
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[ 0.000000] time.c: Using 3.579545 MHz PM timer.
[ 0.000000] time.c: Detected 2211.357 MHz processor.
[ 19.253822] Console: colour VGA+ 80x25
[ 19.254444] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 19.255338] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 19.264754] Memory: 1021208k/1048512k available (2141k kernel code, 26916k reserved, 754k data, 180k init)
[ 19.342026] Calibrating delay using timer specific routine.. 4427.38 BogoMIPS (lpj=8854774)
[ 19.342073] Security Framework v1.0.0 initialized
[ 19.342077] SELinux: Disabled at boot.
[ 19.342096] Mount-cache hash table entries: 256
[ 19.342186] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 19.342189] CPU: L2 Cache: 512K (64 bytes/line)
[ 19.342191] CPU 0(1) -> Node 0 -> Core 0
[ 19.342197] mtrr: v2.0 (20020519)
[ 19.342204] SMP alternatives: switching to UP code
[ 19.342458] checking if image is initramfs... it is
[ 19.833633] Freeing initrd memory: 7094k freed
[ 19.840057] ACPI: Looking for DSDT ... not found!
[ 19.884326] Using local APIC timer interrupts.
[ 19.929544] Detected 12.564 MHz APIC timer.
[ 19.929592] Brought up 1 CPUs
[ 19.929619] time.c: Using PIT/TSC based timekeeping.
[ 19.929621] testing NMI watchdog ... OK.
[ 19.969892] NET: Registered protocol family 16
[ 19.969914] ACPI: bus type pci registered
[ 19.970154] PCI: Using configuration type 1
[ 19.973318] PCI: Using MMCONFIG at e0000000
[ 19.973773] ACPI: Subsystem revision 20051216
[ 19.980257] ACPI: Interpreter enabled
[ 19.980260] ACPI: Using IOAPIC for interrupt routing
[ 19.980733] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 19.980735] PCI: Probing PCI hardware (bus 00)
[ 19.984824] PCI: Transparent bridge - 0000:00:09.0
[ 19.984983] Boot video device is 0000:01:00.0
[ 19.985035] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 20.064273] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 20.065957] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 20.066268] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 20.066576] ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 20.066887] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 20.067200] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 20.067510] ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 20.067818] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 20.068128] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 11 *12 14 15)
[ 20.068439] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 20.068747] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 20.069059] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 11 *12 14 15)
[ 20.069368] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 20.069679] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 20.070004] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 20.070327] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 11 *12 14 15)
[ 20.070649] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 20.071008] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 20.071360] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 20.071711] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 20.072062] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 20.072334] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 20.072698] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[ 20.073064] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[ 20.073429] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 20.073803] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[ 20.074171] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[ 20.074534] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[ 20.074893] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[ 20.075258] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 20.075626] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
[ 20.075995] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[ 20.076366] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[ 20.079748] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 20.079756] pnp: PnP ACPI init
[ 20.085781] pnp: PnP ACPI: found 14 devices
[ 20.085798] PCI: Using ACPI for IRQ routing
[ 20.085801] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 20.085885] PCI-DMA: Disabling IOMMU.
[ 20.086311] pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
[ 20.086314] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
[ 20.086317] pnp: 00:00: ioport range 0x4400-0x447f has been reserved
[ 20.086319] pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
[ 20.086322] pnp: 00:00: ioport range 0x4800-0x487f has been reserved
[ 20.086324] pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
[ 20.086469] PCI: Bridge: 0000:00:09.0
[ 20.086471] IO window: a000-afff
[ 20.086474] MEM window: d0000000-d1ffffff
[ 20.086477] PREFETCH window: 50000000-500fffff
[ 20.086479] PCI: Bridge: 0000:00:0b.0
[ 20.086480] IO window: disabled.
[ 20.086482] MEM window: disabled.
[ 20.086484] PREFETCH window: disabled.
[ 20.086486] PCI: Bridge: 0000:00:0c.0
[ 20.086487] IO window: disabled.
[ 20.086488] MEM window: disabled.
[ 20.086490] PREFETCH window: disabled.
[ 20.086492] PCI: Bridge: 0000:00:0d.0
[ 20.086493] IO window: disabled.
[ 20.086495] MEM window: disabled.
[ 20.086496] PREFETCH window: disabled.
[ 20.086499] PCI: Bridge: 0000:00:0e.0
[ 20.086500] IO window: disabled.
[ 20.086503] MEM window: c8000000-cfffffff
[ 20.086505] PREFETCH window: c0000000-c7ffffff
[ 20.086510] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 20.086516] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 20.086520] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 20.086524] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 20.086528] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 20.086711] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
[ 20.086950] audit: initializing netlink socket (disabled)
[ 20.086958] audit(1151343629.840:1): initialized
[ 20.087064] VFS: Disk quotas dquot_6.5.1
[ 20.087079] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 20.087119] Initializing Cryptographic API
[ 20.087122] io scheduler noop registered
[ 20.087128] io scheduler anticipatory registered
[ 20.087133] io scheduler deadline registered
[ 20.087144] io scheduler cfq registered
[ 20.087475] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 20.087479] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
[ 20.087490] assign_interrupt_mode Found MSI capability
[ 20.087516] Allocate Port Service[pcie00]
[ 20.087543] Allocate Port Service[pcie03]
[ 20.087566] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 20.087569] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
[ 20.087579] assign_interrupt_mode Found MSI capability
[ 20.087592] Allocate Port Service[pcie00]
[ 20.087616] Allocate Port Service[pcie03]
[ 20.087639] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 20.087641] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
[ 20.087652] assign_interrupt_mode Found MSI capability
[ 20.087665] Allocate Port Service[pcie00]
[ 20.087685] Allocate Port Service[pcie03]
[ 20.087710] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 20.087713] pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
[ 20.087723] assign_interrupt_mode Found MSI capability
[ 20.087735] Allocate Port Service[pcie00]
[ 20.087756] Allocate Port Service[pcie03]
[ 20.098483] Real Time Clock Driver v1.12
[ 20.098516] Linux agpgart interface v0.101 (c) Dave Jones
[ 20.098618] PNP: No PS/2 controller found. Probing ports directly.
[ 20.100449] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 20.100688] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 20.100715] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 20.100804] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.102246] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 20.102606] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 20.102644] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 20.102647] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 20.102769] mice: PS/2 mouse device common for all mice
[ 20.103172] NET: Registered protocol family 2
[ 20.137575] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 20.137765] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[ 20.139031] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 20.139654] TCP: Hash tables configured (established 131072 bind 65536)
[ 20.139657] TCP reno registered
[ 20.139728] TCP bic registered
[ 20.139735] NET: Registered protocol family 1
[ 20.139742] NET: Registered protocol family 8
[ 20.139743] NET: Registered protocol family 20
[ 20.139869] ACPI wakeup devices:
[ 20.139871] HUB0 XVR0 XVR1 XVR2 XVR3 USB0 USB2 MMAC MMCI UAR1
[ 20.139876] ACPI: (supports S0 S1 S3 S4 S5)
[ 20.139945] Freeing unused kernel memory: 180k freed
[ 20.171232] vga16fb: initializing
[ 20.171236] vga16fb: mapped to 0xffff8100000a0000
[ 20.375740] Console: switching to colour frame buffer device 80x25
[ 20.375744] fb0: VGA16 VGA frame buffer device
[ 21.485168] Capability LSM initialized
[ 21.505391] ACPI: Fan [FAN] (on)
[ 21.508960] ACPI: Thermal Zone [THRM] (40 C)
[ 21.994280] SCSI subsystem initialized
[ 21.995769] ACPI: bus type scsi registered
[ 21.995772] libata version 1.20 loaded.
[ 21.997124] sata_nv 0000:00:07.0: version 0.8
[ 21.997627] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 21.997632] GSI 16 sharing vector 0xD9 and IRQ 16
[ 21.997636] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 217
[ 21.997752] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 21.997818] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 217
[ 21.997835] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 217
[ 22.205234] ata1: no device found (phy stat 00000000)
[ 22.205237] scsi0 : sata_nv
[ 22.409205] ata2: no device found (phy stat 00000000)
[ 22.409208] scsi1 : sata_nv
[ 22.409943] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[ 22.409949] GSI 17 sharing vector 0xE1 and IRQ 17
[ 22.409953] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 225
[ 22.410051] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 22.410094] ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC400 irq 225
[ 22.410110] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 225
[ 22.781240] ata3: dev 0 cfg 00:0040 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:40ff 93:0000
[ 22.781244] ata3: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
[ 22.785494] sata_get_dev_handle: SATA dev addr=0x80000, handle=0xffff810037fe1340
[ 22.792882] nv_sata: Primary device added
[ 22.792883] nv_sata: Primary device removed
[ 22.792885] nv_sata: Secondary device added
[ 22.792886] nv_sata: Secondary device removed
[ 22.792889] ata3: dev 0 configured for UDMA/133
[ 22.797077] sata_get_dev_handle: SATA dev addr=0x80000, handle=0xffff810037fe1340
[ 22.804362] scsi2 : sata_nv
[ 23.173187] ata4: dev 0 cfg 00:0040 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:40ff 93:0000
[ 23.173192] ata4: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
[ 23.177440] sata_get_dev_handle: SATA dev addr=0x80000, handle=0xffff810037fe1340
[ 23.184826] nv_sata: Primary device added
[ 23.184828] nv_sata: Primary device removed
[ 23.184829] nv_sata: Secondary device added
[ 23.184830] nv_sata: Secondary device removed
[ 23.184833] ata4: dev 0 configured for UDMA/133
[ 23.189030] sata_get_dev_handle: SATA dev addr=0x80000, handle=0xffff810037fe1340
[ 23.196317] scsi3 : sata_nv
[ 23.196951] Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
[ 23.196959] Type: Direct-Access ANSI SCSI revision: 05
[ 23.200669] Driver 'sd' needs updating - please use bus_type methods
[ 23.201175] Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
[ 23.201184] Type: Direct-Access ANSI SCSI revision: 05
[ 23.202726] NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
[ 23.202741] NFORCE-CK804: chipset revision 242
[ 23.202743] NFORCE-CK804: not 100% native mode: will probe irqs later
[ 23.202748] NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
[ 23.202755] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaMA, hdbMA
[ 23.202763] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdcMA, hddMA
[ 23.202769] Probing IDE interface ide0...
[ 23.214736] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[ 23.214772] SCSI device sda: drive cache: write back
[ 23.217267] SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
[ 23.217281] SCSI device sda: drive cache: write back
[ 23.217285] sda: sda1 sda2 < sda5 >
[ 23.242229] sd 2:0:0:0: Attached scsi disk sda
[ 23.242278] SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
[ 23.245675] SCSI device sdb: drive cache: write back
[ 23.249677] SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
[ 23.251807] SCSI device sdb: drive cache: write back
[ 23.251811] sdb: sdb1 < >
[ 23.271963] sd 3:0:0:0: Attached scsi disk sdb
[ 24.221026] hdb: PLEXTOR DVDR PX-716A, ATAPI CD/DVD-ROM drive
[ 24.277105] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 24.278824] Probing IDE interface ide1...
[ 24.856113] hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(66)
[ 24.856121] Uniform CD-ROM driver Revision: 3.20
[ 24.921292] usbcore: registered new driver usbfs
[ 24.921989] usbcore: registered new driver hub
[ 24.923863] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[ 24.924819] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[ 24.924824] GSI 18 sharing vector 0xE9 and IRQ 18
[ 24.924829] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, low) -> IRQ 233
[ 24.924950] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 24.924954] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 24.969574] ieee1394: Initialized config rom entry `ip1394'
[ 24.971023] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 24.971035] ohci_hcd 0000:00:02.0: irq 233, io mem 0xd2004000
[ 24.986970] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
[ 25.030920] hub 1-0:1.0: USB hub found
[ 25.030930] hub 1-0:1.0: 10 ports detected
[ 25.137901] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
[ 25.137907] GSI 19 sharing vector 0x32 and IRQ 19
[ 25.137912] ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCL] -> GSI 20 (level, low) -> IRQ 50
[ 25.138029] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 25.138033] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 25.138061] ehci_hcd 0000:00:02.1: debug port 1
[ 25.138064] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[ 25.138232] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 25.138241] ehci_hcd 0000:00:02.1: irq 50, io mem 0xfeb00000
[ 25.138248] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.138415] hub 2-0:1.0: USB hub found
[ 25.138422] hub 2-0:1.0: 10 ports detected
[ 25.245495] ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
[ 25.245795] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 25.245800] GSI 20 sharing vector 0x3A and IRQ 20
[ 25.245804] ACPI: PCI Interrupt 0000:05:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 58
[ 25.249170] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[ 25.249173] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 217
[ 25.249178] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 25.296649] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[58] MMIO=[d1008000-d10087ff] Max Packet=[2048]
[ 25.664754] usb 2-3: new high speed USB device using ehci_hcd and address 2
[ 25.772992] eth0: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0
[ 25.790893] Probing IDE interface ide1...
[ 25.798678] hub 2-3:1.0: USB hub found
[ 25.798909] hub 2-3:1.0: 4 ports detected
[ 26.089742] ohci_hcd 0000:00:02.0: wakeup
[ 26.377276] Attempting manual resume
[ 26.404506] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.420117] kjournald starting. Commit interval 5 seconds
[ 26.476649] usb 1-4: new low speed USB device using ohci_hcd and address 2
[ 26.568775] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800004216c7]
[ 34.152694] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 34.152717] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 35.493295] NET: Registered protocol family 17
[ 35.738555] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
[ 35.738579] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
[ 35.805643] usbcore: registered new driver hiddev
[ 35.817348] input: Logitech USB Receiver as /class/input/input0
[ 35.817376] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:02.0-4
[ 35.837365] input: Logitech USB Receiver as /class/input/input1
[ 35.837410] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:02.0-4
[ 35.837419] usbcore: registered new driver usbhid
[ 35.837422] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 36.169962] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 36.180661] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 36.192589] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 36.192595] GSI 21 sharing vector 0x42 and IRQ 21
[ 36.192600] ACPI: PCI Interrupt 0000:05:0c.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 66
[ 36.192709] skge 1.3 addr 0xd1000000 irq 66 chip Yukon-Lite rev 9
[ 36.192820] skge eth1: addr 00:13:d4:30:cf:46
[ 36.340223] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
[ 36.340227] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 225
[ 36.340320] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 36.363493] input: PC Speaker as /class/input/input2
[ 36.373317] parport: PnPBIOS parport detected.
[ 36.373364] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 36.392691] Floppy drive(s): fd0 is 1.44M
[ 36.400132] ts: Compaq touchscreen protocol output
[ 36.414981] FDC 0 is a post-1991 82077
[ 36.586249] skge eth1: enabling interface
[ 36.618571] nvidia: module license 'NVIDIA' taints kernel.
[ 36.663583] intel8x0_measure_ac97_clock: measured 59031 usecs
[ 36.663587] intel8x0: clocking to 46964
[ 36.665025] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 36.665031] GSI 22 sharing vector 0x4A and IRQ 22
[ 36.665036] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 74
[ 36.665044] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 36.665163] NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-8762 Mon May 15 13:58:14 PDT 2006
[ 37.367811] lp0: using parport0 (interrupt-driven).
[ 37.407243] sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
[ 37.407246] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[ 37.407248] ieee1394: sbp2: Try serialize_io=0 for better performance
[ 37.460677] Adding 3012148k swap on /dev/sda5. Priority:-1 extents:1 across:3012148k
[ 37.630289] EXT3 FS on sda1, internal journal
[ 37.757114] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 37.757118] md: bitmap version 4.39
[ 38.133304] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[ 44.677273] NET: Registered protocol family 10
[ 44.677372] lo: Disabled Privacy Extensions
[ 44.677688] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 44.677714] IPv6 over IPv4 tunneling driver
[ 55.488636] eth0: no IPv6 routers present
[ 58.171835] ACPI: Power Button (FF) [PWRF]
[ 58.171844] ACPI: Power Button (CM) [PWRB]
[ 58.242117] ibm_acpi: ec object not found
[ 58.269416] pcc_acpi: loading...
[ 58.722973] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
[ 58.727170] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[ 60.121709] ppdev: user-space parallel port driver
[ 63.045925] Bluetooth: Core ver 2.8
[ 63.045929] NET: Registered protocol family 31
[ 63.045931] Bluetooth: HCI device and connection manager initialized
[ 63.045940] Bluetooth: HCI socket layer initialized
[ 63.074217] Bluetooth: L2CAP ver 2.8
[ 63.074220] Bluetooth: L2CAP socket layer initialized
[ 63.077185] Bluetooth: RFCOMM socket layer initialized
[ 63.077199] Bluetooth: RFCOMM TTY layer initialized
[ 63.077201] Bluetooth: RFCOMM ver 1.7
[ 155.879146] usb 2-3.1: new full speed USB device using ehci_hcd and address 4
[ 156.080755] usb 2-3.1: Failed to load zd1201.fw firmware file!
[ 156.080832] usb 2-3.1: Make sure the hotplug firmware loader is installed.
[ 156.080835] usb 2-3.1: Goto http://linux-lc100020.sourceforge.net for more info
[ 156.080837] usb 2-3.1: zd1201 firmware upload failed: -2
[ 156.080840] zd1201: probe of 2-3.1:1.0 failed with error -2
[ 156.080846] usbcore: registered new driver zd1201
[ 184.309606] usbcore: deregistering driver zd1201
matsmarcus@mats-marcus:~$ sudo /sbin/modprobe zd1201
matsmarcus@mats-marcus:~$

edti: ich versuche grad die treiber mir selber zu kompilieren nur leider klappt es nicht:

http://forum.ubuntuusers.de/topic/37110/

Und ich bin in hoffnung auf besserung auf kubuntu umgestiegen; auch weil dies für mich passender erschien (man muss alles mal ausprobieren); desshalb hab ich mich im ubuntuforum versucht. Ein bisschen weiter bin ich nun schon ;-)

Vielleicht habt ihr noch irgendwelche tipps.

Ansonsten vielen Dank für eure Hilfe, auch wenn ich euch jetzt (vorraussichtlich) verlassen werde.

 

[Anonymous]

... Du weisst schon, oder?

[ 155.879146] usb 2-3.1: new full speed USB device using ehci_hcd and address 4
[ 156.080755] usb 2-3.1: Failed to load zd1201.fw firmware file!
[ 156.080832] usb 2-3.1: Make sure the hotplug firmware loader is installed.
[ 156.080835] usb 2-3.1: Goto http://linux-lc100020.sourceforge.net for more info
[ 156.080837] usb 2-3.1: zd1201 firmware upload failed: -2
[ 156.080840] zd1201: probe of 2-3.1:1.0 failed with error -2
[ 156.080846] usbcore: registered new driver zd1201
[ 184.309606] usbcore: deregistering driver zd1201

Klingt interessant, oder?

[Sarkasmus]
Naja, statt zu lesen ist es viel einfacher gleich eine neue Distri zu installieren. Ich hoffe bei Dir auch auf Besserung, wenn nicht, dann empfehle ich eine Lesebrille .[/Sarkasmus]


Greetz,

RM

P.S. Auch bei (K)Ubuntu ist eine der Kernkompetenzen LESEN (Das war mein Tipp zum Abschluss, gern geschehen *fg*)