ThomasF
Hacker
Moin,
also ich hab hier ein Intel Board mit dem 965 Chipsatz ...
lspci sagt :
Beim Versuch diese Kiste mit dem Kernel 2.6.18.2-jen37 zu booten bleibt im ersten Versuch der Bilschirm beim booten schwarz.
Mit den Boot-Parametern noapic und nosmp läuft der Kernel aber hoch.
Nach Abstellen des Bootsplash und der Einstellung auf Textmodus für die Ausgabe beim booten sieht man nur folgende Meldungen :
Und da bleibt er dann stehen ....
Der andere Kernel den ich probiert habe : kernel-default-2.6.18.2-20061120101055.i586.rpm
aus z.B ftp://ftp4.gwdg.de/linux/suse/projects/kernel/kotd/i386/HEAD/
Aber auch alle 2.6.18.2 machen erst mal ein anderes Problem ... der meckert bei der Installation aufgrund einer Abhängigkeit:
perl-Bootloader >= 0.4.1 is needed by kernel-default-xxx
Installierte Version von perl-Bootloader ist 0.2.27-0.4 ... habe auch nirgends eine aktuellere für SuSE gefunden ...
Ich hoffe das hilft dir weiter ?!?
Ich spiele auch gerne Versuchskaninchen ... *fg*
EDIT Ach ja im BIOS steht SATA auf AHCI ... falls das eine Rolle spielen sollte ...
So long
ThomasF
also ich hab hier ein Intel Board mit dem 965 Chipsatz ...
lspci sagt :
00:00.0 Host bridge: Intel Corporation Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation PCI Express Root Port (rev 02)
00:03.0 Communication controller: Intel Corporation HECI Controller (rev 02)
00:1a.0 USB Controller: Intel Corporation USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation PCI Express Port 2 (rev 02)
00:1c.2 PCI bridge: Intel Corporation PCI Express Port 3 (rev 02)
00:1c.3 PCI bridge: Intel Corporation PCI Express Port 4 (rev 02)
00:1c.4 PCI bridge: Intel Corporation PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation LPC Interface Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation SATA Controller AHCI (rev 02)
00:1f.3 SMBus: Intel Corporation SMBus Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation Unknown device 0392 (rev a1)
03:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101 (rev b1)
07:01.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 36)
07:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
Beim Versuch diese Kiste mit dem Kernel 2.6.18.2-jen37 zu booten bleibt im ersten Versuch der Bilschirm beim booten schwarz.
Mit den Boot-Parametern noapic und nosmp läuft der Kernel aber hoch.
Nach Abstellen des Bootsplash und der Einstellung auf Textmodus für die Ausgabe beim booten sieht man nur folgende Meldungen :
SMP alternatives: switch to UP code
*<6>checking if image is initramfs ... *********
**** it is
<6>Freeing initrd memory 2327k freed
ACPI: Core revision 20060707
CPU0 : Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific rautine.. 4795.26 BogoMIPS (lpj=23976345)
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1 : Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9593.14 BogoMIPS).
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Und da bleibt er dann stehen ....
Der andere Kernel den ich probiert habe : kernel-default-2.6.18.2-20061120101055.i586.rpm
aus z.B ftp://ftp4.gwdg.de/linux/suse/projects/kernel/kotd/i386/HEAD/
Aber auch alle 2.6.18.2 machen erst mal ein anderes Problem ... der meckert bei der Installation aufgrund einer Abhängigkeit:
perl-Bootloader >= 0.4.1 is needed by kernel-default-xxx
Installierte Version von perl-Bootloader ist 0.2.27-0.4 ... habe auch nirgends eine aktuellere für SuSE gefunden ...
Ich hoffe das hilft dir weiter ?!?
Ich spiele auch gerne Versuchskaninchen ... *fg*
EDIT Ach ja im BIOS steht SATA auf AHCI ... falls das eine Rolle spielen sollte ...
So long
ThomasF