networkmanager: error getting killswitch power

[author40]

Hallo zusammen,

ich habe zur Zeit probleme mit meinem dell inspiron 1501 eine WLAN-Verbindung aufzubauen. Alles scheint richtig konfiguriert. allerdings ist das icon vom networkmanager mal zu sehen mal nicht. die verbindung ist auch für sekunden vorhanden, funktioniert aber nur, wenn ich mit kabel ins internet will.

mein var/log/networkmanager zeigt mir folgendes:

Feb 22 19:11:58 linux NetworkManager: <info> eth0: Device is fully-supported using driver 'bcm43xx'.
Feb 22 19:11:58 linux NetworkManager: <info> nm_device_init(): waiting for device's worker thread to start
Feb 22 19:11:58 linux NetworkManager: <info> nm_device_init(): device's worker thread started, continuing.
Feb 22 19:11:58 linux NetworkManager: <info> Now managing wireless (802.11) device 'eth0'.
Feb 22 19:11:58 linux NetworkManager: <info> Deactivating device eth0.
Feb 22 19:11:58 linux NetworkManager: <info> Caught terminiation signal
Feb 22 19:11:58 linux NetworkManager: <info> Will activate wired connection 'eth1' because it now has a link.
Feb 22 19:11:58 linux NetworkManager: <debug> [1203703918.226574] nm_print_open_socks(): Open Sockets List:
Feb 22 19:11:58 linux NetworkManager: <debug> [1203703918.226707] nm_print_open_socks(): Open Sockets List Done.
Feb 22 19:11:58 linux NetworkManager: <info> Deactivating device eth1.
Feb 22 19:11:58 linux NetworkManager: <info> Deactivating device eth0.
Feb 22 19:12:01 linux NetworkManager: <WARN> nm_device_802_11_wireless_scan(): could not trigger wireless scan on device eth0: No such device
Feb 22 19:12:01 linux NetworkManager: <info> starting...
Feb 22 19:12:01 linux NetworkManager: <info> Found radio killswitch /org/freedesktop/Hal/devices/dell_wlan_switch
Feb 22 19:12:01 linux NetworkManager: <debug> [1203703921.891430] nm_system_device_get_system_config(): found config '/etc/sysconfig/network/ifcfg-eth1' for interface 'eth1'

Ubuntu scheint beim gutsy ähnliche Probleme zur Zeit zu haben. Ich könnte Hilfe gebrauchen, weiß nicht mehr weiter. Danke.

 

[whois]

HI

Hast du die Karte mit der Traditionellen Methode (Ifup) eingerichtet?
Stell mal bitte das Ergebnis als root aus der Konsole ins Forum.

ifconfig

cu

 

[author40]

Ich habe das leider noch nie mit der ifup Methode gemacht. Der Networkmanager hat immer funktioniert

Hier ein Versuch:

pliebe@linux-dgfo:~> su
Passwort:
su: ungültiges Kennwort
pliebe@linux-dgfo:~> su
Passwort:
linux-dgfo:/home/pliebe # iwconfig
lo no wireless extensions.

eth0 IEEE 802.11g ESSIDff/any
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:32 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption keyff
Power Managementff
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

eth1 no wireless extensions.

linux-dgfo:/home/pliebe # ifup eth0
eth0 device: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01)
eth0 warning: wpa_supplicant already running on interface
DHCP client is already running on eth0
linux-dgfo:/home/pliebe # rmmod ndiswrapper
linux-dgfo:/home/pliebe # modprobe ndiswrapper
linux-dgfo:/home/pliebe # ifdown eth0
eth0 device: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01)
linux-dgfo:/home/pliebe # ifup eth0
eth0 device: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01)
eth0 starting wpa_supplicant
Starting DHCP Client Daemon on eth0... . . . . . no IP address yet... backgrounding.
linux-dgfo:/home/pliebe # ifdown eth1
eth1 device: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
linux-dgfo:/home/pliebe # ifup eth1
eth1 device: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Starting DHCP Client Daemon on eth1... . . . . . IP/Netmask: 192.168.178.23 / 255.255.255.0
linux-dgfo:/home/pliebe # iwconfig
lo no wireless extensions.

eth1 no wireless extensions.

eth0 IEEE 802.11g ESSIDff/any
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:32 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption keyff
Power Managementff
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

linux-dgfo:/home/pliebe # iwlist scanning
lo Interface doesn't support scanning.

eth1 Interface doesn't support scanning.

eth0 Scan completed :
Cell 01 - Address: 00:0D:88:C1:A5:52
ESSID:"/\../\ mmedvs II><II"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.422 GHz (Channel 3)
Quality:31/100 Signal level:-76 dBm Noise level:-96 dBm
Encryption keyn
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Cell 02 - Address: 00:C0:A8:CD:CC:49
ESSID:"3210 Phone WLAN SL"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.437 GHz (Channel 6)
Quality:14/100 Signal level:-87 dBm Noise level:-96 dBm
Encryption keyn
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : TKIP CCMP
Authentication Suites (1) : PSK
Cell 03 - Address: 00:15:0C:CF:C3:95
ESSID:"FRITZ!Box Fon WLAN 7170"
Protocol:IEEE 802.11g
Mode:Managed
Frequency:2.452 GHz (Channel 9)
Quality:79/100 Signal level:-45 dBm Noise level:-96 dBm
Encryption keyn
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK

linux-dgfo:/home/pliebe #
linux-dgfo:/home/pliebe #

Scheint so als wenn das mit dem DHCP nicht funktioniert.