• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

Ralink RT 2860 (ra 0)

Heinz-Peter

Heinz-Peter

Die Ausgabe von dem Kommando iwconfig macht nicht viel Hoffnung.
Sende die Ausgaben von:
Code: 
 hwinfo --netcard
Code: 
 ifconfig
Code: 
iwlist scanning
Code: 
ls -ls /lib/firmware
Code: 
 rpm -qa | grep rt2860
Code: 
modinfo rt2860sta
 
OP
W

Werko1

Habe entsprechende Befehle ausgeführt. Ergebnis folgt:

Code: 
linux-pd1j:~ # hwinfo --netcard
29: PCI 200.0: 0282 WLAN controller                             
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_1814_781
  Unique ID: VQ+S.lp0a+ta+CV3
  Parent ID: z8Q3.6XhEowSpRr2
  SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:02:00.0
  SysFS BusID: 0000:02:00.0
  Hardware Class: network
  Model: "RaLink RT2860"
  Vendor: pci 0x1814 "RaLink"
  Device: pci 0x0781 "RT2860"
  SubVendor: pci 0x1814 "RaLink"
  SubDevice: pci 0x2790 
  Driver: "rt2860"
  Driver Modules: "rt2860sta"
  Device File: ra0
  Features: WLAN
  Memory Range: 0xf3000000-0xf300ffff (rw,non-prefetchable)
  IRQ: 16 (45 events)
  HW Address: 00:22:43:60:59:61
  Link detected: yes
  WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13
  WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472
  WLAN encryption modes: WEP40 WEP104 TKIP CCMP
  WLAN authentication modes: open sharedkey wpa-psk wpa-eap
  Module Alias: "pci:v00001814d00000781sv00001814sd00002790bc02sc80i00"
  Driver Info #0:
    Driver Status: rt2860sta is active
    Driver Activation Cmd: "modprobe rt2860sta"
  Driver Info #1:
    Driver Status: rt2800pci is not active
    Driver Activation Cmd: "modprobe rt2800pci"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)

30: PCI 300.0: 0200 Ethernet controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_10ec_8168
  Unique ID: rBUF.qYglFnxCb40
  Parent ID: qTvu.8Makl3iDVc3
  SysFS ID: /devices/pci0000:00/0000:00:1c.1/0000:03:00.0
  SysFS BusID: 0000:03:00.0
  Hardware Class: network
  Model: "Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
  SubVendor: pci 0x17c0 "Wistron Corp."
  SubDevice: pci 0x10c0 
  Revision: 0x02
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  I/O Ports: 0x3000-0x3fff (rw)
  Memory Range: 0xf3100000-0xf3100fff (rw,non-prefetchable)
  Memory Range: 0xf8000000-0xf800ffff (rw,prefetchable)
  Memory Range: 0xf8020000-0xf803ffff (ro,prefetchable,disabled)
  IRQ: 216 (671 events)
  HW Address: 00:1f:16:13:85:ff
  Link detected: yes
  Module Alias: "pci:v000010ECd00008168sv000017C0sd000010C0bc02sc00i00"
  Driver Info #0:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #16 (PCI bridge)
linux-pd1j:~ # ifconfig
eth0      Link encap:Ethernet  Hardware Adresse 00:1F:16:13:85:FF  
          inet Adresse:192.168.2.102  Bcast:192.168.2.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:336 errors:0 dropped:0 overruns:0 frame:0
          TX packets:363 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:281629 (275.0 Kb)  TX bytes:66453 (64.8 Kb)
          Interrupt:216 Basisadresse:0x4000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:400 (400.0 b)  TX bytes:400 (400.0 b)

ra0       Link encap:Ethernet  Hardware Adresse 00:22:43:60:59:61  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16 

linux-pd1j:~ # iwlist scanning
lo        Interface doesn't support scanning.

ra0       No scan results

eth0      Interface doesn't support scanning.

pan0      Interface doesn't support scanning.

linux-pd1j:~ # iwlist scanning
lo        Interface doesn't support scanning.

ra0       No scan results

eth0      Interface doesn't support scanning.

pan0      Interface doesn't support scanning.

linux-pd1j:~ # ls -ls /lib/firmware
insgesamt 104
4 drwxr-xr-x 14 root root 4096 26. Jul 13:22 2.6.27.7-9-pae
4 -rw-r--r--  1 root root  137  3. Dez 2008  3CCFEM556.cis
4 -rw-r--r--  1 root root  134  3. Dez 2008  3CXEM556.cis
4 -rw-r--r--  1 root root  109  3. Dez 2008  COMpad2.cis
4 -rw-r--r--  1 root root   76  3. Dez 2008  COMpad4.cis
4 -rw-r--r--  1 root root  136  3. Dez 2008  DP83903.cis
4 -rw-r--r--  1 root root   53  3. Dez 2008  E-CARD.cis
4 -rw-r--r--  1 root root  253  3. Dez 2008  LA-PCM.cis
4 -rw-r--r--  1 root root 2142 26. Jun 08:55 LICENSE.ralink-firmware.txt
4 -rw-r--r--  1 root root  107  3. Dez 2008  MT5634ZLX.cis
4 -rw-r--r--  1 root root   54  3. Dez 2008  NE2K.cis
4 -rw-r--r--  1 root root  210  3. Dez 2008  PCMLM28.cis
4 -rw-r--r--  1 root root   68  3. Dez 2008  PE-200.cis
4 -rw-r--r--  1 root root   74  3. Dez 2008  PE520.cis
4 -rw-r--r--  1 root root   86  3. Dez 2008  RS-COM-2P.cis
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561s.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2661.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2860.bin
4 -rw-r--r--  1 root root 4096 26. Jun 08:55 rt2870.bin
4 -rw-r--r--  1 root root 2048 26. Jun 08:55 rt73.bin
4 -rw-r--r--  1 root root   85  3. Dez 2008  tamarack.cis
linux-pd1j:~ # rpm -qa | grep rt2860
linux-pd1j:~ # modinfo rt2860sta
filename:       /lib/modules/2.6.27.7-9-pae/kernel/drivers/staging/rt2860/rt2860sta.ko
version:        1.8.0.0
license:        GPL
srcversion:     57C41D6C031E607F921DD11
alias:          pci:v00001A3Bd00001059sv*sd*bc*sc*i*
alias:          pci:v00001814d00000781sv*sd*bc*sc*i*
alias:          pci:v00001814d00000701sv*sd*bc*sc*i*
alias:          pci:v00001814d00000681sv*sd*bc*sc*i*
alias:          pci:v00001814d00000601sv*sd*bc*sc*i*
depends:        
staging:        Y
vermagic:       2.6.27.7-9-pae SMP mod_unload modversions 586 
parm:           mac:rt28xx: wireless mac addr (charp)
 
OP
W

Werko1

Kann es sein, das es wieder Probleme mit dem Treiber rt2860sta und rt2800pci gibt ?

Code: 
[code]
collectNWData.sh V0.6.1.12 (Rev: 1.162, Build: 2009/06/09 18:29:26)
--- Welcher Netzwerkverbindungtyp soll getestet werden?
--- (2) Kabellose Verbindung (WLAN)
--- Welche Netzwerktopologie liegt vor?
--- (2) WLAN HW router <---> LinuxClient
--- Auf welchem Rechner wird das Script ausgeführt?
--- (1) LinuxClient

!!! CND0380E: Es wurden keine WLANs am Interface ra0 gefunden. Die Hardware und/oder Treiber ist nicht richtig konfiguriert
!!! CND0400W: Es existieren weitere mögliche Module rt2800pci für Interface ra0
--- Gehe zu http://www.linux-tips-and-tricks.de/CND um detailiertere Hinweise zu den Fehlermeldungen/Warnungen zu bekommen und wie die Fehler beseitigt werden können

==================================================================================================================
==================================================================================================================
*** uname -a
Linux linux-pd1j 2.6.27.7-9-pae #1 SMP 2008-12-04 18:10:04 +0100 i686 i686 i386 GNU/Linux
==================================================================================================================
*** cat /etc/*-release
LSB_VERSION="core-2.0-noarch:core-3.2-noarch:core-2.0-ia32:core-3.2-ia32"
openSUSE 11.1 (i586)
VERSION = 11.1
==================================================================================================================
*** cat /etc/resolv | grep -vi "search"
==================================================================================================================
*** cat /etc/hosts
127.0.0.1       localhost
127.0.0.2       linux-pd1j.site linux-pd1j
==================================================================================================================
*** cat /etc/HOSTNAME
linux-pd1j.site
==================================================================================================================
*** route
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
==================================================================================================================
*** ifconfig
eth0      Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#1  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:788 errors:0 dropped:0 overruns:0 frame:0
          TX packets:726 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 SendewarteschlangenlÀnge:1000 
          RX bytes:823227 (803.9 Kb)  TX bytes:114639 (111.9 Kb)
          Interrupt:216 Basisadresse:0x4000 
lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 SendewarteschlangenlÀnge:0 
          RX bytes:400 (400.0 b)  TX bytes:400 (400.0 b)
ra0       Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#2  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 SendewarteschlangenlÀnge:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16 
==================================================================================================================
*** ping tests
connect: Network is unreachable
Ping of 195.135.220.3 failed
ping: unknown host www.suse.de
Ping of www.suse.de failed
==================================================================================================================
*** dhcpcd-test
ra0: No DHCP server detected
==================================================================================================================
*** lspci
02:00.0 Network controller [0280]: RaLink RT2860 [1814:0781]
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
==================================================================================================================
*** lsusb
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 002: ID 04d9:0499 Holtek Semiconductor, Inc. 
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device
Bus 004 Device 002: ID 5986:0102 Acer, Inc Crystal Eye Webcam
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
==================================================================================================================
*** hwinfo --netcard; # (filtered)
29: PCI 200.0: 0282 WLAN controller
  Model: "RaLink RT2860"
  Vendor: pci 0x1814 "RaLink"
  Device: pci 0x0781 "RT2860"
  SubVendor: pci 0x1814 "RaLink"
  SubDevice: pci 0x2790 
  Driver: "rt2860"
  Driver Modules: "rt2860sta"
  Device File: ra0
  Link detected: yes
    Driver Status: rt2860sta is active
    Driver Activation Cmd: "modprobe rt2860sta"
    Driver Status: rt2800pci is not active
    Driver Activation Cmd: "modprobe rt2800pci"
30: PCI 300.0: 0200 Ethernet controller
  Model: "Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
  SubVendor: pci 0x17c0 "Wistron Corp."
  SubDevice: pci 0x10c0 
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  Link detected: no
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
==================================================================================================================
*** lsmod
| ac                      | acpi_cpufreq            | af_packet               | agpgart                  |
| ahci                    | battery                 | binfmt_misc             | bluetooth                |
| bnep                    | bridge                  | button                  | cdrom                    |
| compat_ioctl32          | cpufreq_conservative    | cpufreq_powersave       | cpufreq_userspace        |
| crc_t10dif              | dm_mod                  | dock                    | edd                      |
| ehci_hcd                | ext3                    | fan                     | fat                      |
| ff_memless              | fuse                    | hid                     | hwmon                    |
| i2c_core                | i2c_i801                | intel_agp               | jbd                      |
| joydev                  | l2cap                   | libata                  | loop                     |
| mbcache                 | mii                     | nls_cp437               | nls_iso8859_1            |
| output                  | pcspkr                  | processor               | r8169                    |
| rfcomm                  | rt2860sta               | rtc_cmos                | rtc_core                 |
| rtc_lib                 | sco                     | scsi_mod                | sd_mod                   |
| serio_raw               | sg                      | snd                     | snd_hda_intel            |
| snd_hwdep               | snd_mixer_oss           | snd_page_alloc          | snd_pcm                  |
| snd_pcm_oss             | snd_seq                 | snd_seq_device          | snd_timer                |
| soundcore               | speedstep_lib           | sr_mod                  | stp                      |
| thermal                 | thermal_sys             | uhci_hcd                | usbcore                  |
| usbhid                  | usb_storage             | uvcvideo                | v4l1_compat              |
| vfat                    | video                   | videodev                | wmi                      |
==================================================================================================================
*** cat /etc/sysconfig/network/ifcfg-[earwd]* | egrep -v ".*=''"
==================================================================================================================
*** iwconfig
lo        no wireless extensions.
eth0      no wireless extensions.
pan0      no wireless extensions.
ra0       RT2860 Wireless  ESSID:"§§§§§§§§1"
          Mode:Auto  Frequency=2.412 GHz  Access Point: Not-Associated   
          Bit Rate:1 Mb/s   
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Link Quality=10/100  Signal level:0 dBm  Noise level:-97 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
==================================================================================================================
*** Actual date for bias of following greps
20:18:02 2009-08-17
==================================================================================================================
*** grep -i radio /var/log/boot.msg | tail -n 5
==================================================================================================================
*** dmesg | grep -i radio | tail -n 5
==================================================================================================================
*** tail -n 300 /var/log/messages* | /usr/bin/grep -i firmware | tail -n 5
==================================================================================================================
*** ls /lib/firmware
| 2.6.27.7-9-pae          | 3CCFEM556.cis           | 3CXEM556.cis            | COMpad2.cis              |
| COMpad4.cis             | DP83903.cis             | E-CARD.cis              | LA-PCM.cis               |
| LICENSE.ralink-firmware.txt| MT5634ZLX.cis           | NE2K.cis                | PCMLM28.cis              |
| PE-200.cis              | PE520.cis               | RS-COM-2P.cis           | rt2561.bin               |
| rt2561s.bin             | rt2661.bin              | rt2860.bin              | rt2870.bin               |
| rt73.bin                | tamarack.cis            |
==================================================================================================================
*** ndiswrapper -l
No ndiswrapper module loaded
==================================================================================================================
*** Active processes
wpa_supplicant:YES knetworkmanager:NO nm-applet:YES
==================================================================================================================
*** grep NETWORKMANAGER /etc/sysconfig/network/config
NETWORKMANAGER="yes"
==================================================================================================================
*** grep -i persistent /etc/sysconfig/network/config
==================================================================================================================
*** grep 'eth|ath|wlan|ra' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/70-persistent-net
/usr/bin/egrep: /etc/udev/rules.d/*net_persistent*: Datei oder Verzeichnis nicht gefunden
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#1", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
==================================================================================================================
*** grep -r 'eth[0-10]|ath[0-10]|wlan[0-10]|ra[0-10]' /etc/modprobe.*
/etc/modprobe.conf:install eth0             /bin/true
/etc/modprobe.conf:install eth1             /bin/true
==================================================================================================================
*** iwlist scanning
No WLANs found
==================================================================================================================
*** NWEliza states
IF:eth0  IM:1
IF:ra0  IM:2
DI:2 dI:1 NIC:1 cNiC:2:1 NI:2 cNI:2 NIW:ra0-1 NDIS:0 NIWL:0 CM:2 IP6:0 KM:0 WLW: 0 AP:0
 
OP
W

Werko1

Also jetzt ist mir nichts mehr klar:
In der blacklist stand bisher rt2800pci.
bisher war immer von rt2800pci die Rede - einen Treiber rt2860pci findet mein PC nicht.
Ist das eine Verwechselung oder muß ich einen Treiber mit der Bezeichnung rt2860pci Internet suchen?
 
OP
W

Werko1

Jetzt das Ergebnis mit rt2800pci:
Code: 
linux-pd1j:~ # hwinfo --netcard
29: PCI 200.0: 0282 WLAN controller                             
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_1814_781
  Unique ID: VQ+S.lp0a+ta+CV3
  Parent ID: z8Q3.6XhEowSpRr2
  SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:02:00.0
  SysFS BusID: 0000:02:00.0
  Hardware Class: network
  Model: "RaLink RT2860"
  Vendor: pci 0x1814 "RaLink"
  Device: pci 0x0781 "RT2860"
  SubVendor: pci 0x1814 "RaLink"
  SubDevice: pci 0x2790 
  Driver: "rt2860"
  Driver Modules: "rt2860sta"
  Device File: ra0
  Features: WLAN
  Memory Range: 0xf3000000-0xf300ffff (rw,non-prefetchable)
  IRQ: 16 (127 events)
  HW Address: 00:22:43:60:59:61
  Link detected: yes
  WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13
  WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472
  WLAN encryption modes: WEP40 WEP104 TKIP CCMP
  WLAN authentication modes: open sharedkey wpa-psk wpa-eap
  Module Alias: "pci:v00001814d00000781sv00001814sd00002790bc02sc80i00"
  Driver Info #0:
    Driver Status: rt2860sta is active
    Driver Activation Cmd: "modprobe rt2860sta"
  Driver Info #1:
    Driver Status: rt2800pci is active
    Driver Activation Cmd: "modprobe rt2800pci"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)

30: PCI 300.0: 0200 Ethernet controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_10ec_8168
  Unique ID: rBUF.qYglFnxCb40
  Parent ID: qTvu.8Makl3iDVc3
  SysFS ID: /devices/pci0000:00/0000:00:1c.1/0000:03:00.0
  SysFS BusID: 0000:03:00.0
  Hardware Class: network
  Model: "Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
  SubVendor: pci 0x17c0 "Wistron Corp."
  SubDevice: pci 0x10c0 
  Revision: 0x02
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  I/O Ports: 0x3000-0x3fff (rw)
  Memory Range: 0xf3100000-0xf3100fff (rw,non-prefetchable)
  Memory Range: 0xf8000000-0xf800ffff (rw,prefetchable)
  Memory Range: 0xf8020000-0xf803ffff (ro,prefetchable,disabled)
  IRQ: 216 (5149 events)
  HW Address: 00:1f:16:13:85:ff
  Link detected: yes
  Module Alias: "pci:v000010ECd00008168sv000017C0sd000010C0bc02sc00i00"
  Driver Info #0:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #16 (PCI bridge)
linux-pd1j:~ # ifconfig
eth0      Link encap:Ethernet  Hardware Adresse 00:1F:16:13:85:FF  
          inet Adresse:192.168.2.102  Bcast:192.168.2.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2648 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2727 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:2317194 (2.2 Mb)  TX bytes:526168 (513.8 Kb)
          Interrupt:216 Basisadresse:0x4000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:40 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:2672 (2.6 Kb)  TX bytes:2672 (2.6 Kb)

ra0       Link encap:Ethernet  Hardware Adresse 00:22:43:60:59:61  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16 

linux-pd1j:~ # iwlist scanning
lo        Interface doesn't support scanning.

ra0       No scan results

eth0      Interface doesn't support scanning.

pan0      Interface doesn't support scanning.

linux-pd1j:~ # ls -ls /lib/firmware
insgesamt 104
4 drwxr-xr-x 14 root root 4096 26. Jul 13:22 2.6.27.7-9-pae
4 -rw-r--r--  1 root root  137  3. Dez 2008  3CCFEM556.cis
4 -rw-r--r--  1 root root  134  3. Dez 2008  3CXEM556.cis
4 -rw-r--r--  1 root root  109  3. Dez 2008  COMpad2.cis
4 -rw-r--r--  1 root root   76  3. Dez 2008  COMpad4.cis
4 -rw-r--r--  1 root root  136  3. Dez 2008  DP83903.cis
4 -rw-r--r--  1 root root   53  3. Dez 2008  E-CARD.cis
4 -rw-r--r--  1 root root  253  3. Dez 2008  LA-PCM.cis
4 -rw-r--r--  1 root root 2142 26. Jun 08:55 LICENSE.ralink-firmware.txt
4 -rw-r--r--  1 root root  107  3. Dez 2008  MT5634ZLX.cis
4 -rw-r--r--  1 root root   54  3. Dez 2008  NE2K.cis
4 -rw-r--r--  1 root root  210  3. Dez 2008  PCMLM28.cis
4 -rw-r--r--  1 root root   68  3. Dez 2008  PE-200.cis
4 -rw-r--r--  1 root root   74  3. Dez 2008  PE520.cis
4 -rw-r--r--  1 root root   86  3. Dez 2008  RS-COM-2P.cis
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561s.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2661.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2860.bin
4 -rw-r--r--  1 root root 4096 26. Jun 08:55 rt2870.bin
4 -rw-r--r--  1 root root 2048 26. Jun 08:55 rt73.bin
4 -rw-r--r--  1 root root   85  3. Dez 2008  tamarack.cis
linux-pd1j:~ # rpm -qa | grep rt2860
linux-pd1j:~ # modinfort2800pci
bash: modinfort2800pci: command not found
linux-pd1j:~ # modinfo rt2800pci
filename:       /lib/modules/2.6.27.7-9-pae/updates/drivers/net/wireless/rt2x00/rt2800pci.ko
license:        GPL
firmware:       rt2860.bin
description:    Ralink RT2800 PCI & PCMCIA Wireless LAN driver.
version:        2.3.0
author:         http://rt2x00.serialmonkey.com
srcversion:     3974E9FA1027BD37184AFEF
alias:          pci:v00001A3Bd00001059sv*sd*bc*sc*i*
alias:          pci:v00001814d00003592sv*sd*bc*sc*i*
alias:          pci:v00001814d00003562sv*sd*bc*sc*i*
alias:          pci:v00001814d00003092sv*sd*bc*sc*i*
alias:          pci:v00001814d00003091sv*sd*bc*sc*i*
alias:          pci:v00001814d00003090sv*sd*bc*sc*i*
alias:          pci:v00001814d00003062sv*sd*bc*sc*i*
alias:          pci:v00001814d00000781sv*sd*bc*sc*i*
alias:          pci:v00001814d00000701sv*sd*bc*sc*i*
alias:          pci:v00001814d00000681sv*sd*bc*sc*i*
alias:          pci:v00001814d00000601sv*sd*bc*sc*i*
alias:          pci:v00001432d00007768sv*sd*bc*sc*i*
alias:          pci:v00001432d00007758sv*sd*bc*sc*i*
alias:          pci:v00001432d00007748sv*sd*bc*sc*i*
alias:          pci:v00001432d00007738sv*sd*bc*sc*i*
alias:          pci:v00001432d00007728sv*sd*bc*sc*i*
alias:          pci:v00001432d00007727sv*sd*bc*sc*i*
alias:          pci:v00001432d00007708sv*sd*bc*sc*i*
depends:        built-in,rt2x00lib,rt2x00pci,built-in,built-in,built-in,eeprom_93cx6,crc-ccitt,built-in
vermagic:       2.6.27.7-9-pae SMP mod_unload modversions 586 
parm:           nohwcrypt:Disable hardware encryption. (bool)
 
OP
W

Werko1

Sieht das so besser aus?
Code: 
linux-pd1j:~ # hwinfo --netcard
29: PCI 200.0: 0282 WLAN controller                             
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_1814_781
  Unique ID: VQ+S.lp0a+ta+CV3
  Parent ID: z8Q3.6XhEowSpRr2
  SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:02:00.0
  SysFS BusID: 0000:02:00.0
  Hardware Class: network
  Model: "RaLink RT2860"
  Vendor: pci 0x1814 "RaLink"
  Device: pci 0x0781 "RT2860"
  SubVendor: pci 0x1814 "RaLink"
  SubDevice: pci 0x2790 
  Driver: "rt2860"
  Driver Modules: "rt2860sta"
  Device File: ra0
  Features: WLAN
  Memory Range: 0xf3000000-0xf300ffff (rw,non-prefetchable)
  IRQ: 16 (127 events)
  HW Address: 00:22:43:60:59:61
  Link detected: yes
  WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13
  WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472
  WLAN encryption modes: WEP40 WEP104 TKIP CCMP
  WLAN authentication modes: open sharedkey wpa-psk wpa-eap
  Module Alias: "pci:v00001814d00000781sv00001814sd00002790bc02sc80i00"
  Driver Info #0:
    Driver Status: rt2860sta is active
    Driver Activation Cmd: "modprobe rt2860sta"
  Driver Info #1:
    Driver Status: rt2800pci is active
    Driver Activation Cmd: "modprobe rt2800pci"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)

30: PCI 300.0: 0200 Ethernet controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_10ec_8168
  Unique ID: rBUF.qYglFnxCb40
  Parent ID: qTvu.8Makl3iDVc3
  SysFS ID: /devices/pci0000:00/0000:00:1c.1/0000:03:00.0
  SysFS BusID: 0000:03:00.0
  Hardware Class: network
  Model: "Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
  SubVendor: pci 0x17c0 "Wistron Corp."
  SubDevice: pci 0x10c0 
  Revision: 0x02
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  I/O Ports: 0x3000-0x3fff (rw)
  Memory Range: 0xf3100000-0xf3100fff (rw,non-prefetchable)
  Memory Range: 0xf8000000-0xf800ffff (rw,prefetchable)
  Memory Range: 0xf8020000-0xf803ffff (ro,prefetchable,disabled)
  IRQ: 216 (5880 events)
  HW Address: 00:1f:16:13:85:ff
  Link detected: yes
  Module Alias: "pci:v000010ECd00008168sv000017C0sd000010C0bc02sc00i00"
  Driver Info #0:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #16 (PCI bridge)
linux-pd1j:~ # ifconfig
eth0      Link encap:Ethernet  Hardware Adresse 00:1F:16:13:85:FF  
          inet Adresse:192.168.2.102  Bcast:192.168.2.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3011 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3130 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:2588590 (2.4 Mb)  TX bytes:629984 (615.2 Kb)
          Interrupt:216 Basisadresse:0x4000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:48 errors:0 dropped:0 overruns:0 frame:0
          TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:3240 (3.1 Kb)  TX bytes:3240 (3.1 Kb)

ra0       Link encap:Ethernet  Hardware Adresse 00:22:43:60:59:61  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16 

linux-pd1j:~ # iwlist scanning
lo        Interface doesn't support scanning.

ra0       No scan results

eth0      Interface doesn't support scanning.

pan0      Interface doesn't support scanning.

linux-pd1j:~ # ls -ls /lib/firmware
insgesamt 104
4 drwxr-xr-x 14 root root 4096 26. Jul 13:22 2.6.27.7-9-pae
4 -rw-r--r--  1 root root  137  3. Dez 2008  3CCFEM556.cis
4 -rw-r--r--  1 root root  134  3. Dez 2008  3CXEM556.cis
4 -rw-r--r--  1 root root  109  3. Dez 2008  COMpad2.cis
4 -rw-r--r--  1 root root   76  3. Dez 2008  COMpad4.cis
4 -rw-r--r--  1 root root  136  3. Dez 2008  DP83903.cis
4 -rw-r--r--  1 root root   53  3. Dez 2008  E-CARD.cis
4 -rw-r--r--  1 root root  253  3. Dez 2008  LA-PCM.cis
4 -rw-r--r--  1 root root 2142 26. Jun 08:55 LICENSE.ralink-firmware.txt
4 -rw-r--r--  1 root root  107  3. Dez 2008  MT5634ZLX.cis
4 -rw-r--r--  1 root root   54  3. Dez 2008  NE2K.cis
4 -rw-r--r--  1 root root  210  3. Dez 2008  PCMLM28.cis
4 -rw-r--r--  1 root root   68  3. Dez 2008  PE-200.cis
4 -rw-r--r--  1 root root   74  3. Dez 2008  PE520.cis
4 -rw-r--r--  1 root root   86  3. Dez 2008  RS-COM-2P.cis
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561s.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2661.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2860.bin
4 -rw-r--r--  1 root root 4096 26. Jun 08:55 rt2870.bin
4 -rw-r--r--  1 root root 2048 26. Jun 08:55 rt73.bin
4 -rw-r--r--  1 root root   85  3. Dez 2008  tamarack.cis
linux-pd1j:~ # rpm -qa | grep rt2860
linux-pd1j:~ # modinfo rt2800pci
filename:       /lib/modules/2.6.27.7-9-pae/updates/drivers/net/wireless/rt2x00/rt2800pci.ko
license:        GPL
firmware:       rt2860.bin
description:    Ralink RT2800 PCI & PCMCIA Wireless LAN driver.
version:        2.3.0
author:         http://rt2x00.serialmonkey.com
srcversion:     3974E9FA1027BD37184AFEF
alias:          pci:v00001A3Bd00001059sv*sd*bc*sc*i*
alias:          pci:v00001814d00003592sv*sd*bc*sc*i*
alias:          pci:v00001814d00003562sv*sd*bc*sc*i*
alias:          pci:v00001814d00003092sv*sd*bc*sc*i*
alias:          pci:v00001814d00003091sv*sd*bc*sc*i*
alias:          pci:v00001814d00003090sv*sd*bc*sc*i*
alias:          pci:v00001814d00003062sv*sd*bc*sc*i*
alias:          pci:v00001814d00000781sv*sd*bc*sc*i*
alias:          pci:v00001814d00000701sv*sd*bc*sc*i*
alias:          pci:v00001814d00000681sv*sd*bc*sc*i*
alias:          pci:v00001814d00000601sv*sd*bc*sc*i*
alias:          pci:v00001432d00007768sv*sd*bc*sc*i*
alias:          pci:v00001432d00007758sv*sd*bc*sc*i*
alias:          pci:v00001432d00007748sv*sd*bc*sc*i*
alias:          pci:v00001432d00007738sv*sd*bc*sc*i*
alias:          pci:v00001432d00007728sv*sd*bc*sc*i*
alias:          pci:v00001432d00007727sv*sd*bc*sc*i*
alias:          pci:v00001432d00007708sv*sd*bc*sc*i*
depends:        built-in,rt2x00lib,rt2x00pci,built-in,built-in,built-in,eeprom_93cx6,crc-ccitt,built-in
vermagic:       2.6.27.7-9-pae SMP mod_unload modversions 586 
parm:           nohwcrypt:Disable hardware encryption. (bool)
 
OP
W

Werko1

meine blacklist:
Code: 
# $Id: blacklist 1568 2007-07-12 13:57:29Z zoz $
#
# Listing a module here prevents modprobe from loading it via modalias (only
# aliases from /lib/modules/*/modules.alias). You may still load it explicitely.
# We blacklist some modules becaus they may harm on certain devices or they
# prevent other modules from grabbing the device.
#
# Syntax:  blacklist <driver name>
# See 'man modprobe'.
#

# uhci ... usb-uhci handles the same pci class
blacklist uhci
# usbcore ... module is loaded implicitly, ignore it otherwise
blacklist usbcore

# tulip ... de4x5, xircom_tulip_cb, dmfe (...) handle same devices
blacklist de4x5
# At least 2.4.3 and later xircom_tulip doesn't have that conflict
# xircom_tulip_cb
blacklist dmfe

# list all framebuffer drivers, some of them tend to crash during boot
# they are either compiled into the kernel, or vesafb is active
# X works fine without them, rcfbset can load them if really required
#  sed -e '/\/drivers\/video\/.*\.\(o\|ko\)$/{s@^.*/@@;s@\..*$@@;p};d'
blacklist aty128fb
blacklist atyfb
blacklist clgenfb
blacklist cyber2000fb
blacklist encode-big5
blacklist encode-gb
blacklist encode-gbk
blacklist encode-jis
blacklist encode-kscm
blacklist fbcon-afb
blacklist fbcon-cfb2
blacklist fbcon-cfb4
blacklist fbcon-hga
blacklist fbcon-ilbm
blacklist fbcon-iplan2p2
blacklist fbcon-iplan2p4
blacklist fbcon-iplan2p8
blacklist fbcon-mac
blacklist fbcon-mfb
blacklist fbcon-vga
blacklist fbcon-vga-planes
blacklist fbgen
blacklist g450_pll
blacklist hgafb
blacklist i2c-matroxfb
blacklist i810fb
blacklist intelfbdrv
blacklist intelfbhw
blacklist matroxfb_accel
blacklist matroxfb_base
blacklist matroxfb_crtc2
blacklist matroxfb_DAC1064
blacklist matroxfb_g450
blacklist matroxfb_maven
blacklist matroxfb_misc
blacklist matroxfb_proc
blacklist matroxfb_Ti3026
blacklist mdacon
blacklist neofb
blacklist pm2fb
blacklist pm3fb
blacklist radeonfb
blacklist rivafb
blacklist sisfb
blacklist sstfb
blacklist tdfxfb
blacklist tridentfb
blacklist unikey
blacklist vga16fb
blacklist vgastate
blacklist vmware
# for kyrofb see Bug 35810
blacklist kyrofb
# list was not complete (bug 106715)
blacklist arcfb
blacklist backlight
blacklist lcd
blacklist cirrusfb
blacklist gx1fb
blacklist intelfb
blacklist macmodes
blacklist nvidiafb
blacklist s1d13xxxfb
blacklist savagefb
blacklist rt2800pci

# ISDN modules are load from /lib/udev/isdn.sh
blacklist fcusb
blacklist fcusb2
blacklist fxusb
blacklist fxusb_CZ
blacklist fcdslusb
blacklist fcdslusb2
blacklist fcdslusba
blacklist fcdslslusb
blacklist fcdslslusb2
blacklist e2220pc
blacklist e5520pc
blacklist bfusb
blacklist b1isa
blacklist b1pci
blacklist b1pcmcia
blacklist c4
blacklist t1isa
blacklist t1pci
blacklist divas
blacklist act2000
blacklist hfc_usb
blacklist hisax
blacklist hisax_fcpcipnp
blacklist hisax_st5481
blacklist hysdn
blacklist icn
blacklist pcbit
blacklist sc
blacklist tpam
blacklist fcpci
blacklist fcclassic
blacklist fcdsl
blacklist fcdsl2

# OSS PCI sound modules
blacklist ad1889
blacklist ali5455
blacklist btaudio
blacklist cmpci
blacklist cs4281
blacklist emu10k1
blacklist es1370
blacklist es1371
blacklist esssolo1
blacklist forte
blacklist i810_audio
blacklist maestro
blacklist maestro3
blacklist nm256_audio
blacklist opl3sa2                 # Bug 219758
blacklist rme96xx
blacklist sonicvibes
blacklist trident
blacklist via82cxxx_audio
blacklist ymfpci

# If you really need firewire direct networking, then remove this entry
blacklist eth1394

# this is a debugging module which should only be loaded manually
blacklist evbug

# These mtd drivers should be loaded manually.
blacklist scb2_flash
blacklist ich2rom
blacklist pci
blacklist l440gx
blacklist amd76xrom

# job of rcdvb
blacklist snd_bt87x
blacklist snd-bt87x

# HP Touch Screen usb input driver. breaks all other mouse input devices
blacklist tsdev

# The TPM modules are supposed to support the Trusted Platform chip.
# The TPM is connected to the LPC bus, so these modules logically need to
# specify the PCI ID of the LPC interface.
# It's probably a reasonable thing to disable automatic loading of these
# modules, given that we're not doing much with them anyway ATM.
# In the future we may need a bit of more intelligent scanning of devices
# that are connected to busses such as LPC or I2C.
blacklist tpm_infineon
blacklist tpm_nsc
blacklist tpm_atmel

# https://bugzilla.novell.com/show_bug.cgi?id=115132
blacklist slamr
blacklist slusb

# This module seems to be good for nothing. See bug 129301.
blacklist dpt_i2o

# This driver is obsolete and should never be loaded as default.
# See https://bugzilla.novell.com/show_bug.cgi?id=146728
blacklist eepro100

# This driver is obsolete and should never be loaded as default.
# See https://bugzilla.novell.com/show_bug.cgi?id=146930
blacklist sk98lin

# This driver is rarely needed and causes trouble when scanning devices.
# See: https://bugzilla.novell.com/show_bug.cgi?id=144623
blacklist stradis

# These devices have bt878 chip without PCI Subsystem ID. Without that info bttv
# does not know how to treat them properly. Therefore we disable autoloading of
# modules for these devices.
# See https://bugzilla.novell.com/show_bug.cgi?id=149588
# To enable your device create a hardware configuration file for your device.
# See man hwup for details.
# You will probably have to specify an option to identify your card. Have a
# look in /usr/src/linux/Documentation/video4linux/CARDLIST.bttv.
alias pci:v0000109Ed0000036Esv00000000sd00000000bc04sc00i00 bttv_skip_it
alias pci:v0000109Ed00000878sv00000000sd00000000bc04sc80i00 bttv_skip_it
install bttv_skip_it /bin/echo "module alias skipped (bt878 chip without PCI Subsystem ID)"

# For some bridges both intel-agp and i82875p_edac are loaded. If i82875p_edac
# is loaded first it will grab the device. Then intel-agp doesn't work.
# Therefore we disable automatic loading of 82875p_edac. (Bug 213840)
blacklist i82875p_edac
 
OP
W

Werko1

Ergebnis:
Code: 
linux-pd1j:~ # cat /etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program run by the persistent-net-generator.rules rules file.
#
# You can modify it,as long as you keep each rule on a single line.
# PCI device 0x10ec:0x8168 (r8169)
# This file was automatically generated by the /lib/udev/write_net_rules
# program run by the persistent-net-generator.rules rules file.
#
# You can modify it,as long as you keep each rule on a single line.
# PCI device 0x10ec:0x8168 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:1f:16:13:85:ff", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
 
Heinz-Peter

Heinz-Peter

Umbenenne die original Datei in 70-persistent-net.backup dann abspeichern.
Neue Datei öffnen und das rein kopieren:
Code: 
# This file was automatically generated by the /lib/udev/write_net_rules
# program run by the persistent-net-generator.rules rules file.
#
# You can modify it,as long as you keep each rule on a single line.
# PCI device 0x10ec:0x8168 (r8169)
# This file was automatically generated by the /lib/udev/write_net_rules
# program run by the persistent-net-generator.rules rules file.
#
# You can modify it,as long as you keep each rule on a single line.
# PCI device 0x10ec:0x8168 (r8169)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:1f:16:13:85:ff", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:22:43:60:59:61", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
#
 
OP
W

Werko1

Hatte bereits damit begonnen und noch weitere Befehle probiert:
Code: 
 hwinfo --netcard
29: PCI 200.0: 0282 WLAN controller                             
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_1814_781
  Unique ID: VQ+S.lp0a+ta+CV3
  Parent ID: z8Q3.6XhEowSpRr2
  SysFS ID: /devices/pci0000:00/0000:00:1c.0/0000:02:00.0
  SysFS BusID: 0000:02:00.0
  Hardware Class: network
  Model: "RaLink RT2860"
  Vendor: pci 0x1814 "RaLink"
  Device: pci 0x0781 "RT2860"
  SubVendor: pci 0x1814 "RaLink"
  SubDevice: pci 0x2790 
  Driver: "rt2860"
  Driver Modules: "rt2860sta"
  Device File: ra0
  Features: WLAN
  Memory Range: 0xf3000000-0xf300ffff (rw,non-prefetchable)
  IRQ: 16 (127 events)
  HW Address: 00:22:43:60:59:61
  Link detected: yes
  WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13
  WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472
  WLAN encryption modes: WEP40 WEP104 TKIP CCMP
  WLAN authentication modes: open sharedkey wpa-psk wpa-eap
  Module Alias: "pci:v00001814d00000781sv00001814sd00002790bc02sc80i00"
  Driver Info #0:
    Driver Status: rt2860sta is active
    Driver Activation Cmd: "modprobe rt2860sta"
  Driver Info #1:
    Driver Status: rt2800pci is not active
    Driver Activation Cmd: "modprobe rt2800pci"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #15 (PCI bridge)

30: PCI 300.0: 0200 Ethernet controller
  [Created at pci.318]
  UDI: /org/freedesktop/Hal/devices/pci_10ec_8168
  Unique ID: rBUF.qYglFnxCb40
  Parent ID: qTvu.8Makl3iDVc3
  SysFS ID: /devices/pci0000:00/0000:00:1c.1/0000:03:00.0
  SysFS BusID: 0000:03:00.0
  Hardware Class: network
  Model: "Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller"
  Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
  Device: pci 0x8168 "RTL8111/8168B PCI Express Gigabit Ethernet controller"
  SubVendor: pci 0x17c0 "Wistron Corp."
  SubDevice: pci 0x10c0 
  Revision: 0x02
  Driver: "r8169"
  Driver Modules: "r8169"
  Device File: eth0
  I/O Ports: 0x3000-0x3fff (rw)
  Memory Range: 0xf3100000-0xf3100fff (rw,non-prefetchable)
  Memory Range: 0xf8000000-0xf800ffff (rw,prefetchable)
  Memory Range: 0xf8020000-0xf803ffff (ro,prefetchable,disabled)
  IRQ: 216 (3111 events)
  HW Address: 00:1f:16:13:85:ff
  Link detected: yes
  Module Alias: "pci:v000010ECd00008168sv000017C0sd000010C0bc02sc00i00"
  Driver Info #0:
    Driver Status: r8169 is active
    Driver Activation Cmd: "modprobe r8169"
  Config Status: cfg=no, avail=yes, need=no, active=unknown
  Attached to: #16 (PCI bridge)
linux-pd1j:~ # ifconfig
eth0      Link encap:Ethernet  Hardware Adresse 00:1F:16:13:85:FF  
          inet Adresse:192.168.2.102  Bcast:192.168.2.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1531 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1694 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:1365254 (1.3 Mb)  TX bytes:338603 (330.6 Kb)
          Interrupt:216 Basisadresse:0xe000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:40 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:0 
          RX bytes:2672 (2.6 Kb)  TX bytes:2672 (2.6 Kb)

ra0       Link encap:Ethernet  Hardware Adresse 00:22:43:60:59:61  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:16 

linux-pd1j:~ # iwlist scanning
lo        Interface doesn't support scanning.

ra0       No scan results

eth0      Interface doesn't support scanning.

pan0      Interface doesn't support scanning.

linux-pd1j:~ # ls -ls /lib/firmware
insgesamt 104
4 drwxr-xr-x 14 root root 4096 26. Jul 13:22 2.6.27.7-9-pae
4 -rw-r--r--  1 root root  137  3. Dez 2008  3CCFEM556.cis
4 -rw-r--r--  1 root root  134  3. Dez 2008  3CXEM556.cis
4 -rw-r--r--  1 root root  109  3. Dez 2008  COMpad2.cis
4 -rw-r--r--  1 root root   76  3. Dez 2008  COMpad4.cis
4 -rw-r--r--  1 root root  136  3. Dez 2008  DP83903.cis
4 -rw-r--r--  1 root root   53  3. Dez 2008  E-CARD.cis
4 -rw-r--r--  1 root root  253  3. Dez 2008  LA-PCM.cis
4 -rw-r--r--  1 root root 2142 26. Jun 08:55 LICENSE.ralink-firmware.txt
4 -rw-r--r--  1 root root  107  3. Dez 2008  MT5634ZLX.cis
4 -rw-r--r--  1 root root   54  3. Dez 2008  NE2K.cis
4 -rw-r--r--  1 root root  210  3. Dez 2008  PCMLM28.cis
4 -rw-r--r--  1 root root   68  3. Dez 2008  PE-200.cis
4 -rw-r--r--  1 root root   74  3. Dez 2008  PE520.cis
4 -rw-r--r--  1 root root   86  3. Dez 2008  RS-COM-2P.cis
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2561s.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2661.bin
8 -rw-r--r--  1 root root 8192 26. Jun 08:55 rt2860.bin
4 -rw-r--r--  1 root root 4096 26. Jun 08:55 rt2870.bin
4 -rw-r--r--  1 root root 2048 26. Jun 08:55 rt73.bin
4 -rw-r--r--  1 root root   85  3. Dez 2008  tamarack.cis
linux-pd1j:~ # rpm -qa | grep rt2860
molinux-pd1j:~ # modinfo rt2800pci
filename:       /lib/modules/2.6.27.7-9-pae/updates/drivers/net/wireless/rt2x00/rt2800pci.ko
license:        GPL
firmware:       rt2860.bin
description:    Ralink RT2800 PCI & PCMCIA Wireless LAN driver.
version:        2.3.0
author:         http://rt2x00.serialmonkey.com
srcversion:     3974E9FA1027BD37184AFEF
alias:          pci:v00001A3Bd00001059sv*sd*bc*sc*i*
alias:          pci:v00001814d00003592sv*sd*bc*sc*i*
alias:          pci:v00001814d00003562sv*sd*bc*sc*i*
alias:          pci:v00001814d00003092sv*sd*bc*sc*i*
alias:          pci:v00001814d00003091sv*sd*bc*sc*i*
alias:          pci:v00001814d00003090sv*sd*bc*sc*i*
alias:          pci:v00001814d00003062sv*sd*bc*sc*i*
alias:          pci:v00001814d00000781sv*sd*bc*sc*i*
alias:          pci:v00001814d00000701sv*sd*bc*sc*i*
alias:          pci:v00001814d00000681sv*sd*bc*sc*i*
alias:          pci:v00001814d00000601sv*sd*bc*sc*i*
alias:          pci:v00001432d00007768sv*sd*bc*sc*i*
alias:          pci:v00001432d00007758sv*sd*bc*sc*i*
alias:          pci:v00001432d00007748sv*sd*bc*sc*i*
alias:          pci:v00001432d00007738sv*sd*bc*sc*i*
alias:          pci:v00001432d00007728sv*sd*bc*sc*i*
alias:          pci:v00001432d00007727sv*sd*bc*sc*i*
alias:          pci:v00001432d00007708sv*sd*bc*sc*i*
depends:        built-in,rt2x00lib,rt2x00pci,built-in,built-in,built-in,eeprom_93cx6,crc-ccitt,built-in
vermagic:       2.6.27.7-9-pae SMP mod_unload modversions 586 
parm:           nohwcrypt:Disable hardware encryption. (bool)
linux-pd1j:~ # modinfo rt2860sta
filename:       /lib/modules/2.6.27.7-9-pae/kernel/drivers/staging/rt2860/rt2860sta.ko
version:        1.8.0.0
license:        GPL
srcversion:     57C41D6C031E607F921DD11
alias:          pci:v00001A3Bd00001059sv*sd*bc*sc*i*
alias:          pci:v00001814d00000781sv*sd*bc*sc*i*
alias:          pci:v00001814d00000701sv*sd*bc*sc*i*
alias:          pci:v00001814d00000681sv*sd*bc*sc*i*
alias:          pci:v00001814d00000601sv*sd*bc*sc*i*
depends:        
staging:        Y
vermagic:       2.6.27.7-9-pae SMP mod_unload modversions 586 
parm:           mac:rt28xx: wireless mac addr (charp)
linux-pd1j:~ # iwconfig
lo        no wireless extensions.

ra0       RT2860 Wireless  ESSID:""  Nickname:"RT2860STA"
          Mode:Auto  Frequency=2.412 GHz  Access Point: Not-Associated   
          Bit Rate:1 Mb/s   
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Link Quality=10/100  Signal level:0 dBm  Noise level:-97 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

eth0      no wireless extensions.

pan0      no wireless extensions.
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben