Realtek RTL8139D und PC/104 Board mit VIA Chipset

lc1 · 3 Juli 2008

Hallo an alle die hoffentlich mehr Ahnung haben als ich,

Ich habe hier ein PC/104 Board vom Typ PCM-3370 von Advantech liegen.
Nun wollte ich darauf Suse bzw. eine andere Distri installieren.
So weit so gut da installieren geht ja eigentlich ganz leicht von der Hand so mit USB-DVD Laufwerk und co.
Nun komme ich allerdings an den punkt wo ich den Netzwerkchip ansprechen will (Realtek RTL8139DL kennung 0x10EC 0x8139)

Und da sieh mal einer an ...... da ist ja keiner. --> ich komm nicht drauf wo der sich versteckt hat.

Vom Bios wird der Netzwerkcontroller als IRQ 11 auf PCI BUS 0 Device 15 gelistet (bitte nicht festnageln kann auch gering abweichen)

Hier mal die Auszüge aus

lspci

Code:

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266] (rev 02)

lspci -v

Code:

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
	Subsystem: VIA Technologies, Inc. VT8605 [ProSavage PM133]
	Flags: bus master, medium devsel, latency 0
	Memory at e8000000 (32-bit, prefetchable) [size=32M]
	Capabilities: [a0] AGP version 2.0
	Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, medium devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: ea000000-ebffffff
	Prefetchable memory behind bridge: e0000000-e7ffffff
	Capabilities: [80] Power Management version 2

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
	Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
	Flags: bus master, stepping, medium devsel, latency 0
	Capabilities: [c0] Power Management version 2
	Kernel modules: parport_pc

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
	Flags: bus master, medium devsel, latency 32
	I/O ports at e000 [size=16]
	Capabilities: [c0] Power Management version 2

00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI])
	Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
	Flags: bus master, medium devsel, latency 32, IRQ 10
	I/O ports at e400 [size=32]
	Capabilities: [80] Power Management version 2
	Kernel modules: usb-uhci, uhci

00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
	Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
	Flags: medium devsel, IRQ 5
	Capabilities: [68] Power Management version 2

01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266] (rev 02) (prog-if 00 [VGA controller])
	Flags: bus master, 66MHz, medium devsel, latency 32
	Memory at eb000000 (32-bit, non-prefetchable) [size=512K]
	Memory at e0000000 (32-bit, prefetchable) [size=128M]
	Expansion ROM at <unassigned> [disabled] [size=64K]
	Capabilities: [dc] Power Management version 2
	Capabilities: [80] AGP version 2.0

dmesg

Code:

<4>Linux version 2.4.31 (root@box) (gcc version 2.95.4 20011002 (Debian prerelease)) #6 SMP Fri Oct 21 15:15:54 EDT 2005
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
<4> BIOS-e820: 000000000dff0000 - 000000000dff3000 (ACPI NVS)
<4> BIOS-e820: 000000000dff3000 - 000000000e000000 (ACPI data)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<5>0MB HIGHMEM available.
<5>223MB LOWMEM available.
<4>On node 0 totalpages: 57328
<4>zone(0): 4096 pages.
<4>zone(1): 53232 pages.
<4>zone(2): 0 pages.
<6>ACPI: RSDP (v000 VIA606                                    ) @ 0x000f6f50
<6>ACPI: RSDT (v001 VIA606 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3000
<6>ACPI: FADT (v001 VIA606 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3040
<6>ACPI: DSDT (v001 VIA606 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
<4>Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off vga=791 initrd=minirt24.gz nomce noapic qemu quiet BOOT_IMAGE=knoppix frugal BOOT_IMAGE=linux24 
<4>No local APIC present or hardware disabled
<6>Initializing CPU#0
<4>Detected 400.027 MHz processor.
<4>Console: colour dummy device 80x25
<4>Calibrating delay loop... 797.90 BogoMIPS
<6>Memory: 222808k/229312k available (1386k kernel code, 6116k reserved, 567k data, 144k init, 0k highmem)
<6>Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
<6>Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
<4>Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 256K
<7>CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
<7>CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<6>Checking for popad bug... OK.
<4>ACPI: IRQ5 SCI: Level Trigger.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 256K
<7>CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
<7>CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
<4>CPU0: Intel Mobile Intel(R) Celeron(TM) CPU          400MHz stepping 04
<4>per-CPU timeslice cutoff: 730.25 usecs.
<5>SMP motherboard not detected.
<5>Local APIC not detected. Using dummy APIC emulation.
<4>Waiting on wait_init_idle (map = 0x0)
<4>All processors have done init_idle
<6>ACPI: Subsystem revision 20040326
<6>PCI: PCI BIOS revision 2.10 entry at 0xfa940, last bus=1
<6>PCI: Using configuration type 1
<6>ACPI: Interpreter enabled
<6>ACPI: Using PIC for interrupt routing
<6>ACPI: System [ACPI] (supports S0 S1 S4bios S5)
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Via IRQ fixup
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
<6>PCI: Probing PCI hardware
<4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
<6>PCI: Using ACPI for IRQ routing
<6>PCI: Disabling Via external APIC routing
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<5>VFS: Disk quotas vdquot_6.5.1
<6>vesafb: framebuffer at 0xe0000000, mapped to 0xce813000, size 3072k
<6>vesafb: mode is 1024x768x16, linelength=2048, pages=19
<6>vesafb: protected mode interface info at c000:76f7
<6>vesafb: scrolling: redraw
<6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
<4>Console: switching to colour frame buffer device 128x48
<6>fb0: VESA VGA frame buffer device
<4>pty: 256 Unix98 ptys configured
<6>Floppy drive(s): fd0 is unknown type 12 (usb?)
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>VP_IDE: IDE controller at PCI slot 00:07.1
<6>VP_IDE: chipset revision 6
<6>VP_IDE: not 100% native mode: will probe irqs later
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
<6>    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
<6>    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:pio
<4>hdc: CF CARD 2GB, ATA DISK drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hdc: attached ide-disk driver.
<6>hdc: 3964464 sectors (2030 MB) w/1KiB Cache, CHS=3933/16/63
<6>Partition check:
<6> hdc: [PTBL] [246/255/63] hdc1
<4>ide: late registration of driver.
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<6>Initializing Cryptographic API
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 2048 buckets, 16Kbytes
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 840k freed
<4>EXT2-fs warning: checktime reached, running e2fsck is recommended
<4>VFS: Mounted root (ext2 filesystem).
<6>scsi0 : SCSI host adapter emulation for IDE ATAPI devices
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<6>usb-uhci.c: $Revision: 1.275 $ time 14:05:13 Aug 18 2005
<6>usb-uhci.c: High bandwidth mode enabled
<6>usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 10
<4>usb-uhci.c: Detected 2 ports
<6>usb.c: new USB bus registered, assigned bus number 1
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<6>usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
<6>Initializing USB Mass Storage driver...
<6>usb.c: registered new driver usb-storage
<6>USB Mass Storage support registered.
<6>hub.c: new USB device 00:07.2-1, assigned address 2
<6>scsi1 : SCSI emulation for USB Mass Storage devices
<4>  Vendor:           Model: USB DISK Pro      Rev: PMAP
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
<4>SCSI device sda: 243200 512-byte hdwr sectors (125 MB)
<4>sda: Write Protect is off
<6> sda: sda1
<7>WARNING: USB Mass Storage data integrity not assured
<7>USB Mass Storage device found at 2
<4>Unable to identify CD-ROM format.
<4>VFS: Can't find ext2 filesystem on dev ide1(22,0).
<4>FAT: bogus logical sector size 1766
<4>VFS: Can't find a valid FAT filesystem on dev 16:00.
<4>Unable to identify CD-ROM format.
<4>VFS: Can't find ext2 filesystem on dev sd(8,1).
<4>Unable to identify CD-ROM format.
<4>VFS: Can't find ext2 filesystem on dev ide1(22,1).
<4>cloop: Initializing cloop v2.01
<6>cloop: loaded (max 128 devices)
<4>cloop: /cdrom/KNOPPIX/KNOPPIX: 1833 blocks, 65536 bytes/block, largest block is 65552 bytes.
<7>ISO 9660 Extensions: RRIP_1991A
<6>Freeing unused kernel memory: 144k freed
<6>Real Time Clock Driver v1.10f
<6>ACPI: Power Button (FF) [PWRF]
<6>ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
<6>Linux Kernel Card Services 3.1.22
<6>  options:  [pci] [cardbus] [pm]
<6>Intel ISA PCIC probe: not found.
<6>Databook TCIC-2 PCMCIA probe: not found.
<4>usbdevfs: remount parameter error
<6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>parport0: PC-style at 0x378 [PCSPP,EPP]
<6>parport_pc: Via 686A parallel port: io=0x378
<6>parport0: PC-style at 0x378 [PCSPP,EPP]
<6>parport_pc: Via 686A parallel port: io=0x378
<6>Linux agpgart interface v0.99 (c) Jeff Hartmann
<6>agpgart: Maximum main memory to use for agp memory: 176M
<3>agpgart: Unsupported Via chipset (device id: 0605), you might want to try agp_try_unsupported=1.
<7>agpgart: no supported devices found.
<6>Linux agpgart interface v0.99 (c) Jeff Hartmann
<6>agpgart: Maximum main memory to use for agp memory: 176M
<4>agpgart: Trying generic Via routines for device id: 0605
<6>agpgart: AGP aperture is 32M @ 0xe8000000
<4>Registering unionfs 1.0.14
<6>usb.c: registered new driver hiddev
<6>usb.c: registered new driver hid
<6>hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
<6>hid-core.c: USB HID support drivers
<6>mice: PS/2 mouse device common for all mice
<6>apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
<5>apm: overridden by ACPI.
<6>usb.c: USB disconnect on device 00:07.2-1 address 2
<6>hub.c: new USB device 00:07.2-1, assigned address 3
<6>scsi2 : SCSI emulation for USB Mass Storage devices
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
<5>sdb: Unit Not Ready, sense:
<4>Current 00:00: sns = 70  2
<4>ASC=3a ASCQ= 0
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
<4>sdb : READ CAPACITY failed.
<4>sdb : status = 1, message = 00, host = 0, driver = 08 
<4>Current sd00:00: sns = 70  2
<4>ASC=3a ASCQ= 0
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
<4>sdb : block size assumed to be 512 bytes, disk size 1GB.  
<6> sdb: I/O error: dev 08:10, sector 0
<4> I/O error: dev 08:10, sector 0
<4> unable to read partition table
<7>WARNING: USB Mass Storage data integrity not assured
<7>USB Mass Storage device found at 3
<6>scsi singledevice 1 0 0 1
<6>scsi singledevice 1 0 0 2
<6>scsi singledevice 1 0 0 3
<6>scsi singledevice 1 0 0 4
<6>scsi singledevice 1 0 0 5
<6>scsi singledevice 1 0 0 6
<6>scsi singledevice 2 0 0 1
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 1
<4>SCSI device sdc: 2880 512-byte hdwr sectors (1 MB)
<4>sdc: Write Protect is off
<6> sdc: sdc1 sdc2 sdc3 sdc4
<6>scsi singledevice 2 0 0 2
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 2
<4>SCSI device sdd: 2880 512-byte hdwr sectors (1 MB)
<4>sdd: Write Protect is off
<6> sdd: sdd1 sdd2 sdd3 sdd4
<6>scsi singledevice 2 0 0 3
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 3
<4>SCSI device sde: 2880 512-byte hdwr sectors (1 MB)
<4>sde: Write Protect is off
<6> sde: sde1 sde2 sde3 sde4
<6>scsi singledevice 2 0 0 4
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdf at scsi2, channel 0, id 0, lun 4
<4>SCSI device sdf: 2880 512-byte hdwr sectors (1 MB)
<4>sdf: Write Protect is off
<6> sdf: sdf1 sdf2 sdf3 sdf4
<6>scsi singledevice 2 0 0 5
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdg at scsi2, channel 0, id 0, lun 5
<4>SCSI device sdg: 2880 512-byte hdwr sectors (1 MB)
<4>sdg: Write Protect is off
<6> sdg: sdg1 sdg2 sdg3 sdg4
<6>scsi singledevice 2 0 0 6
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdh at scsi2, channel 0, id 0, lun 6
<4>SCSI device sdh: 2880 512-byte hdwr sectors (1 MB)
<4>sdh: Write Protect is off
<6> sdh: sdh1 sdh2 sdh3 sdh4
<5>sda: Unit Not Ready, sense:
<4>Info fld=0xa00 (nonstd), Current 00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Info fld=0xa00 (nonstd), Current sd00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<4>sda: test WP failed, assume Write Enabled
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<4> I/O error: dev 08:21, sector 0
<4> I/O error: dev 08:23, sector 0
<4> I/O error: dev 08:24, sector 0
<4> I/O error: dev 08:31, sector 0
<4> I/O error: dev 08:33, sector 0
<4> I/O error: dev 08:34, sector 0
<4> I/O error: dev 08:41, sector 0
<4> I/O error: dev 08:43, sector 0
<4> I/O error: dev 08:44, sector 0
<4> I/O error: dev 08:51, sector 0
<4> I/O error: dev 08:53, sector 0
<4> I/O error: dev 08:54, sector 0
<4> I/O error: dev 08:61, sector 0
<4> I/O error: dev 08:63, sector 0
<4> I/O error: dev 08:64, sector 0
<4> I/O error: dev 08:71, sector 0
<5>sda: Unit Not Ready, sense:
<4>Info fld=0xa00 (nonstd), Current 00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Info fld=0xa00 (nonstd), Current sd00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<4>sda: test WP failed, assume Write Enabled
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<4> I/O error: dev 08:00, sector 2096896
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 128
<4> I/O error: dev 08:00, sector 144
<4> I/O error: dev 08:00, sector 128
<4> I/O error: dev 08:00, sector 128
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 80
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 32
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 8
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 8
<4> I/O error: dev 08:00, sector 8
<4> I/O error: dev 08:00, sector 24
<4> I/O error: dev 08:00, sector 24
<4> I/O error: dev 08:73, sector 0
<4> I/O error: dev 08:74, sector 0
<4>SCSI device sdb: 2880 512-byte hdwr sectors (1 MB)
<4>sdb: Write Protect is off
<6> sdb: sdb1 sdb2 sdb3 sdb4

Kann es sein das hier die BIOS Tabelle falsch ist die an die Kernel geht oder wie krieg ich die Kernel dazu mir den Netzwerkchip zu finden.

Hier ist der Link zu dem Board: http://taiwan.advantech.com.tw/unzipfunc/unziplit.asp?Literature_ID=1-FFZD1
Auf Seite 2 sieht man den aufbau mit dem VIA Chipset

P.S die Files stammen von einem DSL.

Anonymous · 3 Juli 2008

lc1 schrieb:
Hier mal die Auszüge aus

Hier dachte ich mir

"OK, Auszüge aus dmesg und dafür aber lspci vollständig, macht ja Sinn"

Hm, seltsam ...

lspci

Code:

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266] (rev 02)

Also wenn das alles ist, dann gibt es da keine Netzwerkkarte und wenn es ein Auszug ist, dann warum der Teil, der offensichtlich keine Netzwerkkarte enthält?

Wenn lspci nichts findet, dann ist das > 99% gleichbedeutend mit "physikalisch nicht vorhanden/angeschlossen".

Aber gut, dann zumindest nur ein relevanter Auszug aus der dmesg statt des vollen Programms.

Code:

<4>Linux version 2.4.31 (root@box) (gcc version 2.95.4 20011002 (Debian prerelease)) #6 SMP Fri Oct 21 15:15:54 EDT 2005
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
<4> BIOS-e820: 000000000dff0000 - 000000000dff3000 (ACPI NVS)
<4> BIOS-e820: 000000000dff3000 - 000000000e000000 (ACPI data)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<5>0MB HIGHMEM available.
<5>223MB LOWMEM available.
<4>On node 0 totalpages: 57328
<4>zone(0): 4096 pages.
<4>zone(1): 53232 pages.
<4>zone(2): 0 pages.
<6>ACPI: RSDP (v000 VIA606                                    ) @ 0x000f6f50
<6>ACPI: RSDT (v001 VIA606 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3000
<6>ACPI: FADT (v001 VIA606 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3040
<6>ACPI: DSDT (v001 VIA606 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
<4>Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off vga=791 initrd=minirt24.gz nomce noapic qemu quiet BOOT_IMAGE=knoppix frugal BOOT_IMAGE=linux24 
<4>No local APIC present or hardware disabled
<6>Initializing CPU#0
<4>Detected 400.027 MHz processor.
<4>Console: colour dummy device 80x25
<4>Calibrating delay loop... 797.90 BogoMIPS
<6>Memory: 222808k/229312k available (1386k kernel code, 6116k reserved, 567k data, 144k init, 0k highmem)
<6>Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
<6>Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<6>Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
<4>Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 256K
<7>CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
<7>CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<6>Checking for popad bug... OK.
<4>ACPI: IRQ5 SCI: Level Trigger.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
<4>mtrr: detected mtrr type: Intel
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 256K
<7>CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
<7>CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
<4>CPU0: Intel Mobile Intel(R) Celeron(TM) CPU          400MHz stepping 04
<4>per-CPU timeslice cutoff: 730.25 usecs.
<5>SMP motherboard not detected.
<5>Local APIC not detected. Using dummy APIC emulation.
<4>Waiting on wait_init_idle (map = 0x0)
<4>All processors have done init_idle
<6>ACPI: Subsystem revision 20040326
<6>PCI: PCI BIOS revision 2.10 entry at 0xfa940, last bus=1
<6>PCI: Using configuration type 1
<6>ACPI: Interpreter enabled
<6>ACPI: Using PIC for interrupt routing
<6>ACPI: System [ACPI] (supports S0 S1 S4bios S5)
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<6>PCI: Via IRQ fixup
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<4>ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
<4>ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
<6>PCI: Probing PCI hardware
<4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
<6>PCI: Using ACPI for IRQ routing
<6>PCI: Disabling Via external APIC routing
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<5>VFS: Disk quotas vdquot_6.5.1
<6>vesafb: framebuffer at 0xe0000000, mapped to 0xce813000, size 3072k
<6>vesafb: mode is 1024x768x16, linelength=2048, pages=19
<6>vesafb: protected mode interface info at c000:76f7
<6>vesafb: scrolling: redraw
<6>vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
<4>Console: switching to colour frame buffer device 128x48
<6>fb0: VESA VGA frame buffer device
<4>pty: 256 Unix98 ptys configured
<6>Floppy drive(s): fd0 is unknown type 12 (usb?)
<6>FDC 0 is a post-1991 82077
<4>RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>VP_IDE: IDE controller at PCI slot 00:07.1
<6>VP_IDE: chipset revision 6
<6>VP_IDE: not 100% native mode: will probe irqs later
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:07.1
<6>    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
<6>    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:pio
<4>hdc: CF CARD 2GB, ATA DISK drive
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hdc: attached ide-disk driver.
<6>hdc: 3964464 sectors (2030 MB) w/1KiB Cache, CHS=3933/16/63
<6>Partition check:
<6> hdc: [PTBL] [246/255/63] hdc1
<4>ide: late registration of driver.
<6>SCSI subsystem driver Revision: 1.00
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
<6>Initializing Cryptographic API
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 2048 buckets, 16Kbytes
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<5>RAMDISK: Compressed image found at block 0
<6>Freeing initrd memory: 840k freed
<4>EXT2-fs warning: checktime reached, running e2fsck is recommended
<4>VFS: Mounted root (ext2 filesystem).
<6>scsi0 : SCSI host adapter emulation for IDE ATAPI devices
<6>usb.c: registered new driver usbdevfs
<6>usb.c: registered new driver hub
<6>usb-uhci.c: $Revision: 1.275 $ time 14:05:13 Aug 18 2005
<6>usb-uhci.c: High bandwidth mode enabled
<6>usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 10
<4>usb-uhci.c: Detected 2 ports
<6>usb.c: new USB bus registered, assigned bus number 1
<6>hub.c: USB hub found
<6>hub.c: 2 ports detected
<6>usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
<6>Initializing USB Mass Storage driver...
<6>usb.c: registered new driver usb-storage
<6>USB Mass Storage support registered.
<6>hub.c: new USB device 00:07.2-1, assigned address 2
<6>scsi1 : SCSI emulation for USB Mass Storage devices
<4>  Vendor:           Model: USB DISK Pro      Rev: PMAP
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
<4>SCSI device sda: 243200 512-byte hdwr sectors (125 MB)
<4>sda: Write Protect is off
<6> sda: sda1
<7>WARNING: USB Mass Storage data integrity not assured
<7>USB Mass Storage device found at 2
<4>Unable to identify CD-ROM format.
<4>VFS: Can't find ext2 filesystem on dev ide1(22,0).
<4>FAT: bogus logical sector size 1766
<4>VFS: Can't find a valid FAT filesystem on dev 16:00.
<4>Unable to identify CD-ROM format.
<4>VFS: Can't find ext2 filesystem on dev sd(8,1).
<4>Unable to identify CD-ROM format.
<4>VFS: Can't find ext2 filesystem on dev ide1(22,1).
<4>cloop: Initializing cloop v2.01
<6>cloop: loaded (max 128 devices)
<4>cloop: /cdrom/KNOPPIX/KNOPPIX: 1833 blocks, 65536 bytes/block, largest block is 65552 bytes.
<7>ISO 9660 Extensions: RRIP_1991A
<6>Freeing unused kernel memory: 144k freed
<6>Real Time Clock Driver v1.10f
<6>ACPI: Power Button (FF) [PWRF]
<6>ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
<6>Linux Kernel Card Services 3.1.22
<6>  options:  [pci] [cardbus] [pm]
<6>Intel ISA PCIC probe: not found.
<6>Databook TCIC-2 PCMCIA probe: not found.
<4>usbdevfs: remount parameter error
<6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<6>parport0: PC-style at 0x378 [PCSPP,EPP]
<6>parport_pc: Via 686A parallel port: io=0x378
<6>parport0: PC-style at 0x378 [PCSPP,EPP]
<6>parport_pc: Via 686A parallel port: io=0x378
<6>Linux agpgart interface v0.99 (c) Jeff Hartmann
<6>agpgart: Maximum main memory to use for agp memory: 176M
<3>agpgart: Unsupported Via chipset (device id: 0605), you might want to try agp_try_unsupported=1.
<7>agpgart: no supported devices found.
<6>Linux agpgart interface v0.99 (c) Jeff Hartmann
<6>agpgart: Maximum main memory to use for agp memory: 176M
<4>agpgart: Trying generic Via routines for device id: 0605
<6>agpgart: AGP aperture is 32M @ 0xe8000000
<4>Registering unionfs 1.0.14
<6>usb.c: registered new driver hiddev
<6>usb.c: registered new driver hid
<6>hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
<6>hid-core.c: USB HID support drivers
<6>mice: PS/2 mouse device common for all mice
<6>apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
<5>apm: overridden by ACPI.
<6>usb.c: USB disconnect on device 00:07.2-1 address 2
<6>hub.c: new USB device 00:07.2-1, assigned address 3
<6>scsi2 : SCSI emulation for USB Mass Storage devices
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdb at scsi2, channel 0, id 0, lun 0
<5>sdb: Unit Not Ready, sense:
<4>Current 00:00: sns = 70  2
<4>ASC=3a ASCQ= 0
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
<4>sdb : READ CAPACITY failed.
<4>sdb : status = 1, message = 00, host = 0, driver = 08 
<4>Current sd00:00: sns = 70  2
<4>ASC=3a ASCQ= 0
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 
<4>sdb : block size assumed to be 512 bytes, disk size 1GB.  
<6> sdb: I/O error: dev 08:10, sector 0
<4> I/O error: dev 08:10, sector 0
<4> unable to read partition table
<7>WARNING: USB Mass Storage data integrity not assured
<7>USB Mass Storage device found at 3
<6>scsi singledevice 1 0 0 1
<6>scsi singledevice 1 0 0 2
<6>scsi singledevice 1 0 0 3
<6>scsi singledevice 1 0 0 4
<6>scsi singledevice 1 0 0 5
<6>scsi singledevice 1 0 0 6
<6>scsi singledevice 2 0 0 1
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdc at scsi2, channel 0, id 0, lun 1
<4>SCSI device sdc: 2880 512-byte hdwr sectors (1 MB)
<4>sdc: Write Protect is off
<6> sdc: sdc1 sdc2 sdc3 sdc4
<6>scsi singledevice 2 0 0 2
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdd at scsi2, channel 0, id 0, lun 2
<4>SCSI device sdd: 2880 512-byte hdwr sectors (1 MB)
<4>sdd: Write Protect is off
<6> sdd: sdd1 sdd2 sdd3 sdd4
<6>scsi singledevice 2 0 0 3
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sde at scsi2, channel 0, id 0, lun 3
<4>SCSI device sde: 2880 512-byte hdwr sectors (1 MB)
<4>sde: Write Protect is off
<6> sde: sde1 sde2 sde3 sde4
<6>scsi singledevice 2 0 0 4
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdf at scsi2, channel 0, id 0, lun 4
<4>SCSI device sdf: 2880 512-byte hdwr sectors (1 MB)
<4>sdf: Write Protect is off
<6> sdf: sdf1 sdf2 sdf3 sdf4
<6>scsi singledevice 2 0 0 5
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdg at scsi2, channel 0, id 0, lun 5
<4>SCSI device sdg: 2880 512-byte hdwr sectors (1 MB)
<4>sdg: Write Protect is off
<6> sdg: sdg1 sdg2 sdg3 sdg4
<6>scsi singledevice 2 0 0 6
<4>  Vendor: NEC       Model: USB UF000x        Rev: 1.60
<4>  Type:   Direct-Access                      ANSI SCSI revision: 02
<4>Attached scsi removable disk sdh at scsi2, channel 0, id 0, lun 6
<4>SCSI device sdh: 2880 512-byte hdwr sectors (1 MB)
<4>sdh: Write Protect is off
<6> sdh: sdh1 sdh2 sdh3 sdh4
<5>sda: Unit Not Ready, sense:
<4>Info fld=0xa00 (nonstd), Current 00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Info fld=0xa00 (nonstd), Current sd00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<4>sda: test WP failed, assume Write Enabled
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<4> I/O error: dev 08:21, sector 0
<4> I/O error: dev 08:23, sector 0
<4> I/O error: dev 08:24, sector 0
<4> I/O error: dev 08:31, sector 0
<4> I/O error: dev 08:33, sector 0
<4> I/O error: dev 08:34, sector 0
<4> I/O error: dev 08:41, sector 0
<4> I/O error: dev 08:43, sector 0
<4> I/O error: dev 08:44, sector 0
<4> I/O error: dev 08:51, sector 0
<4> I/O error: dev 08:53, sector 0
<4> I/O error: dev 08:54, sector 0
<4> I/O error: dev 08:61, sector 0
<4> I/O error: dev 08:63, sector 0
<4> I/O error: dev 08:64, sector 0
<4> I/O error: dev 08:71, sector 0
<5>sda: Unit Not Ready, sense:
<4>Info fld=0xa00 (nonstd), Current 00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : READ CAPACITY failed.
<4>sda : status = 1, message = 00, host = 0, driver = 08 
<4>Info fld=0xa00 (nonstd), Current sd00:00: sns = 70  2
<4>Raw sense data:0x70 0x00 0x02 0x00 0x00 0x0a 0x00 0x00 
<4>sda : block size assumed to be 512 bytes, disk size 1GB.  
<4>sda: test WP failed, assume Write Enabled
<6> sda: I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> unable to read partition table
<4> I/O error: dev 08:00, sector 2096896
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 128
<4> I/O error: dev 08:00, sector 144
<4> I/O error: dev 08:00, sector 128
<4> I/O error: dev 08:00, sector 128
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 80
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 64
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 32
<4> I/O error: dev 08:00, sector 16
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 8
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 0
<4> I/O error: dev 08:00, sector 8
<4> I/O error: dev 08:00, sector 8
<4> I/O error: dev 08:00, sector 24
<4> I/O error: dev 08:00, sector 24
<4> I/O error: dev 08:73, sector 0
<4> I/O error: dev 08:74, sector 0
<4>SCSI device sdb: 2880 512-byte hdwr sectors (1 MB)
<4>sdb: Write Protect is off
<6> sdb: sdb1 sdb2 sdb3 sdb4

*MÖÖÖP*

wieder daneben ..... (heute ist nicht mein Tag.)

Aber immerhin steht eines fest.

Wenn das Mainboard im selben "guten" Zustand, wie die scheinbar gerade in fröhlicher Eintracht sterbende

Festplatte

ist (wie viele sind da überhaupt drin? bei sde hab ich aufgehört zu zählen ...., aber egal die schmeissen eh alle die selben I/O-Errors aus), dann würde ich die gleich gemeinsam entsorgen.

Ach ja, BTW:

lc1 schrieb:
P.S die Files stammen von einem DSL.

Das hat aber Kernel 2.4, also ein denkbar schlechtes Testgelände für eine geplante Installation einer Distribution mit 2.6er Kernel.

Greetz,

RM

lc1 · 4 Juli 2008

Achso na ja war nicht mehr ganz wach ;-)
Die "auszüge" sind vollständig.

Hier mal was Fedora meldet und da ist eine 2.6er Kernel am laufen

dmesg

Code:

SMP alternatives: switching to UP code
Freeing SMP alternatives: 20k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0020 (from 0c20)
CPU0: Intel Mobile Intel(R) Celeron(TM) CPU          400MHz stepping 04
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=3712 bytes
CPU0 attaching sched-domain:
 domain 0: span 00000001
  groups: 00000001
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
Time:  7:29:36  Date: 07/04/08
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfa7f0, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.4: quirk: region 6000-607f claimed by vt82c686 HW-mon
pci 0000:00:07.4: quirk: region 5000-500f claimed by vt82c686 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
system 00:00: iomem range 0xf0000-0xf3fff could not be reserved
system 00:00: iomem range 0xf4000-0xf7fff could not be reserved
system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0xeff0000-0xeffffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0xefeffff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: 0xec000000-0xedffffff
  PREFETCH window: 0x00000000e0000000-0x00000000e7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
 it is
Freeing initrd memory: 9368k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
type=2000 audit(1215156579.008:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
pci 0000:00:07.0: Disabling VIA external APIC routing
pci 0000:01:00.0: Boot video device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 2 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
agpgart: Detected VIA ProSavage PM133/PL133/PN133 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
  Magic number: 0:970:469
Freeing unused kernel memory: 284k freed
Write protecting the kernel read-only data: 908k
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
loop: module loaded
Floppy drive(s): fd0 is unknown type 12 (usb?)
FDC 0 is a post-1991 82077
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
input: PC Speaker as /devices/platform/pcspkr/input/input2
input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input3
squashfs: version 3.3 (2007/10/31) Phillip Lougher
SCSI subsystem initialized
Loading iSCSI transport class v2.0-869.
iscsi: registered transport (tcp)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000e400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25-14.fc9.i586 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb 1-2: new full speed USB device using uhci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: New USB device found, idVendor=152e, idProduct=2507
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: Super Multi Rewriter
usb 1-2: Manufacturer: HLDS Inc.
usb 1-2: SerialNumber: P010610280348200
libata version 3.00 loaded.
pata_via 0000:00:07.1: version 0.3.3
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15
ata2.00: ATA-4: PQI Industrial CF Card, ra6h.a01, max UDMA/33
ata2.00: 983040 sectors, multi 1: LBA 
ata2.00: configured for UDMA/33
scsi 1:0:0:0: Direct-Access     ATA      PQI Industrial C ra6h PQ: 0 ANSI: 5
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] 983040 512-byte hardware sectors (503 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 983040 512-byte hardware sectors (503 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: unknown partition table
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
Marking TSC unstable due to: TSC halts in idle.
usb-storage: device scan complete
scsi 2:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-E10L  LE05 PQ: 0 ANSI: 0
scsi 2:0:0:0: Attached scsi generic sg1 type 5
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
ISO 9660 Extensions: Microsoft Joliet Level 3
Unable to load NLS charset utf8
Unable to load NLS charset utf8
ISO 9660 Extensions: RRIP_1991A
ISOFS: Unable to identify CD-ROM format.
VFS: Can't find an ext2 filesystem on dev loop0.
SELinux:8192 avtab hash slots allocated. Num of rules:172315
SELinux:8192 avtab hash slots allocated. Num of rules:172315
security:  5 users, 12 roles, 2301 types, 116 bools, 1 sens, 1024 cats
security:  72 classes, 172315 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev loop0, type squashfs), not configured for labeling
SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: policy loaded with handle_unknown=allow
type=1403 audit(1215156607.777:2): policy loaded auid=4294967295 ses=4294967295
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :   884.000 MB/sec
xor: using function: pIII_sse (884.000 MB/sec)
async_tx: api initialized (async)
raid6: int32x1    109 MB/s
raid6: int32x2    132 MB/s
raid6: int32x4    105 MB/s
raid6: int32x8     97 MB/s
raid6: mmxx1      343 MB/s
raid6: mmxx2      390 MB/s
raid6: sse1x1     324 MB/s
raid6: sse1x2     417 MB/s
raid6: using algorithm sse1x2 (417 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
md: linear personality registered for level -1
GFS2 (built May  1 2008 05:50:44) installed
Lock_Nolock (built May  1 2008 05:50:53) installed
JFS: nTxBlock = 1866, nTxLock = 14931
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath emc: version 0.0.3 loaded

floppy driver state
-------------------
now=4294740926 last interrupt=4294740061 diff=865 last called handler=cf8a7163
timeout_message=lock fdc
last output bytes:
14 90 4294672120
18 80 4294672120
 8 80 4294672121
 8 80 4294672121
 8 80 4294672121
 8 80 4294672121
12 80 4294737966
 0 90 4294737966
13 90 4294737966
 0 90 4294737966
1a 90 4294737966
 0 90 4294737966
 3 80 4294737966
81 90 4294737966
10 90 4294737966
 7 80 4294737966
 0 90 4294737966
 8 81 4294740061
 7 80 4294740081
 0 90 4294740081
last result at 4294740061
last redo_fd_request at 4294737926
70  0 
status=81
fdc_busy=1
do_floppy=cf8a7163
cont=cf8acd84
current_req=00000000
command_status=-1

floppy0: floppy timeout called
floppy0: unexpected interrupt 
floppy0: sensei repl[0]=70 repl[1]=0 
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
usb 1-1: new full speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb 1-1: New USB device found, idVendor=0d7d, idProduct=1620
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB DISK Pro    
usb 1-1: Manufacturer:         
usb 1-1: SerialNumber: 074B0B30007F
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 3:0:0:0: Direct-Access              USB DISK Pro     PMAP PQ: 0 ANSI: 0 CCS
scsi 3:0:0:1: Direct-Access              USB DISK Pro     PMAP PQ: 0 ANSI: 0 CCS
sd 3:0:0:0: [sdb] 243200 512-byte hardware sectors (125 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 243200 512-byte hardware sectors (125 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb4
sd 3:0:0:0: [sdb] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:1: [sdc] 2880 512-byte hardware sectors (1 MB)
sd 3:0:0:1: [sdc] Write Protect is off
sd 3:0:0:1: [sdc] Mode Sense: 23 94 00 00
sd 3:0:0:1: [sdc] Assuming drive cache: write through
sd 3:0:0:1: [sdc] 2880 512-byte hardware sectors (1 MB)
sd 3:0:0:1: [sdc] Write Protect is off
sd 3:0:0:1: [sdc] Mode Sense: 23 94 00 00
sd 3:0:0:1: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 3:0:0:1: [sdc] Attached SCSI removable disk
sd 3:0:0:1: Attached scsi generic sg3 type 0
FAT: bogus number of FAT structure
VFS: Can't find a valid FAT filesystem on dev sdc1.
GFS2: Unrecognized block device or mount point /dev/sdc1
GFS2: gfs2 mount does not exist
SELinux: initialized (dev sdc, type vfat), uses genfs_contexts

lspci

Code:

00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a)
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
01:00.0 VGA compatible controller: S3 Inc. 86C380 [ProSavageDDR K4M266] (rev 02)

und vom BIOS wird der Ethernet Controller als Bus 00 Device 15 Function 1 Angezeit --> ??00:15.1?? oder so

Realtek RTL8139D und PC/104 Board mit VIA Chipset

lc1

Anonymous

Gast

lc1