• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

Smartd Temp in Celcius anzeigen

F

Fendria

Hi,

die Meldungen in /var/log/messages werden bei mir immer mit den internen Werten angezeigt obwohl ich, wie googlerecherche ergeben hat, angegeben habe er solle es in Celsius angeben

Meine smartd.conf:

/dev/sda -d sat -a -R 194 -s (S/../.././02|L/../../6/03)
/dev/sdb -d sat -a -R 194 -s (S/../.././02|L/../../6/03)

laut google wird mit -R 194 die anzeige in temparatur erzwungen.

Kann mir hier jmd helfen?
Danke
 
RME

RME

Hallo,

Ist "-d sat" für Dich korrekt? (alternativ: weglassen, oder "-d ata" ?)

Gruss,
Roland
 
OP
F

Fendria

Aehm es sind SATA II platten also ist es richtig oder?
Habs jetzt mal weggelassen mal schauen obs jetzt geht
 
RME

RME

Wie sieht denn Deine /etc/smartd.conf aus?

Code: 
> cat /etc/smartd.conf
und was zeigt:

Code: 
# smartctl -a /dev/sda  | grep Temperature
 
OP
F

Fendria

smartd.conf:

Ohne Kommentare:
Code: 
DEVICESCAN -d removable
/dev/sda -a -R 231 -s (S/../.././02|L/../../6/03) -m server@rottmann-moebel.de
/dev/sdb -a -R 231 -s (S/../.././02|L/../../6/03) -m server@rottmann-moebel.de

Mit Kommentaren:
Code: 
# Sample configuration file for smartd.  See man smartd.conf.

# Home page is: http://smartmontools.sourceforge.net

# $Id: smartd.conf 3128 2010-07-27 13:08:31Z chrfranke $

# smartd will re-read the configuration file if it receives a HUP
# signal

# The file gives a list of devices to monitor using smartd, with one
# device per line. Text after a hash (#) is ignored, and you may use
# spaces and tabs for white space. You may use '\' to continue lines.

# You can usually identify which hard disks are on your system by
# looking in /proc/ide and in /proc/scsi.

# The word DEVICESCAN will cause any remaining lines in this
# configuration file to be ignored: it tells smartd to scan for all
# ATA and SCSI devices.  DEVICESCAN may be followed by any of the
# Directives listed below, which will be applied to all devices that
# are found.  Most users should comment out DEVICESCAN and explicitly
# list the devices that they wish to monitor.
# Adding -d removable prevents error messages after disconnecting of
# monitored removable discs.
#DEVICESCAN -d removable
DEVICESCAN -d removable

# Alternative setting to ignore temperature and power-on hours reports
# in syslog.
#DEVICESCAN -d removable -I 194 -I 231 -I 9

# Alternative setting to report more useful raw temperature in syslog.
#DEVICESCAN -d removable -R 194 -R 231 -I 9

# Alternative setting to report raw temperature changes >= 5 Celsius
# and min/max temperatures.
#DEVICESCAN -d removable -I 194 -I 231 -I 9 -W 5

# First (primary) ATA/IDE hard disk.  Monitor all attributes, enable
# automatic online data collection, automatic Attribute autosave, and
# start a short self-test every day between 2-3am, and a long self test
# Saturdays between 3-4am.
#/dev/hda -a -o on -S on -s (S/../.././02|L/../../6/03)

# Monitor SMART status, ATA Error Log, Self-test log, and track
# changes in all attributes except for attribute 194
#/dev/hdb -H -l error -l selftest -t -I 194

# Monitor all attributes except normalized Temperature (usually 194),
# but track Temperature changes >= 4 Celsius, report Temperatures
# >= 45 Celsius and changes in Raw value of Reallocated_Sector_Ct (5).
# Send mail on SMART failures or when Temperature is >= 55 Celsius.
#/dev/hdc -a -I 194 -W 4,45,55 -R 5 -m admin@example.com

# An ATA disk may appear as a SCSI device to the OS. If a SCSI to
# ATA Translation (SAT) layer is between the OS and the device then
# this can be flagged with the '-d sat' option. This situation may
# become common with SATA disks in SAS and FC environments.
# /dev/sda -a -d sat

# A very silent check.  Only report SMART health status if it fails
# But send an email in this case
#/dev/hdc -H -C 0 -U 0 -m admin@example.com

# First two SCSI disks.  This will monitor everything that smartd can
# monitor.  Start extended self-tests Wednesdays between 6-7pm and
# Sundays between 1-2 am
/dev/sda -a -R 231 -s (S/../.././02|L/../../6/03) -m server@rottmann-moebel.de
/dev/sdb -a -R 231 -s (S/../.././02|L/../../6/03) -m server@rottmann-moebel.de

# Monitor 4 ATA disks connected to a 3ware 6/7/8000 controller which uses
# the 3w-xxxx driver. Start long self-tests Sundays between 1-2, 2-3, 3-4,
# and 4-5 am.
# NOTE: starting with the Linux 2.6 kernel series, the /dev/sdX interface
# is DEPRECATED.  Use the /dev/tweN character device interface instead.
# For example /dev/twe0, /dev/twe1, and so on.
#/dev/sdc -d 3ware,0 -a -s L/../../7/01
#/dev/sdc -d 3ware,1 -a -s L/../../7/02
#/dev/sdc -d 3ware,2 -a -s L/../../7/03
#/dev/sdc -d 3ware,3 -a -s L/../../7/04

# Monitor 2 ATA disks connected to a 3ware 9000 controller which
# uses the 3w-9xxx driver (Linux, FreeBSD). Start long self-tests Tuesdays
# between 1-2 and 3-4 am.
#/dev/twa0 -d 3ware,0 -a -s L/../../2/01
#/dev/twa0 -d 3ware,1 -a -s L/../../2/03

# Monitor 2 SATA (not SAS) disks connected to a 3ware 9000 controller which
# uses the 3w-sas driver (Linux, FreeBSD). Start long self-tests Tuesdays
# between 1-2 and 3-4 am.
#/dev/twl0 -d 3ware,0 -a -s L/../../2/01
#/dev/twa0 -d 3ware,1 -a -s L/../../2/03

# Same as above for Windows. Option '-d 3ware,N' is not necessary,
# disk (port) number is specified in device name.
# NOTE: On Windows, DEVICESCAN works also for 3ware controllers.
#/dev/hdc,0 -a -s L/../../2/01
#/dev/hdc,1 -a -s L/../../2/03

# Monitor 3 ATA disks directly connected to a HighPoint RocketRAID. Start long
# self-tests Sundays between 1-2, 2-3, and 3-4 am.
#/dev/sdd -d hpt,1/1 -a -s L/../../7/01
#/dev/sdd -d hpt,1/2 -a -s L/../../7/02
#/dev/sdd -d hpt,1/3 -a -s L/../../7/03

# Monitor 2 ATA disks connected to the same PMPort which connected to the
# HighPoint RocketRAID. Start long self-tests Tuesdays between 1-2 and 3-4 am
#/dev/sdd -d hpt,1/4/1 -a -s L/../../2/01
#/dev/sdd -d hpt,1/4/2 -a -s L/../../2/03

# HERE IS A LIST OF DIRECTIVES FOR THIS CONFIGURATION FILE.
# PLEASE SEE THE smartd.conf MAN PAGE FOR DETAILS
#
#   -d TYPE Set the device type: ata, scsi, marvell, removable, 3ware,N, hpt,L/M/N
#   -T TYPE set the tolerance to one of: normal, permissive
#   -o VAL  Enable/disable automatic offline tests (on/off)
#   -S VAL  Enable/disable attribute autosave (on/off)
#   -n MODE No check. MODE is one of: never, sleep, standby, idle
#   -H      Monitor SMART Health Status, report if failed
#   -l TYPE Monitor SMART log.  Type is one of: error, selftest
#   -f      Monitor for failure of any 'Usage' Attributes
#   -m ADD  Send warning email to ADD for -H, -l error, -l selftest, and -f
#   -M TYPE Modify email warning behavior (see man page)
#   -s REGE Start self-test when type/date matches regular expression (see man page)
#   -p      Report changes in 'Prefailure' Normalized Attributes
#   -u      Report changes in 'Usage' Normalized Attributes
#   -t      Equivalent to -p and -u Directives
#   -r ID   Also report Raw values of Attribute ID with -p, -u or -t
#   -R ID   Track changes in Attribute ID Raw value with -p, -u or -t
#   -i ID   Ignore Attribute ID for -f Directive
#   -I ID   Ignore Attribute ID for -p, -u or -t Directive
#   -C ID   Report if Current Pending Sector count non-zero
#   -U ID   Report if Offline Uncorrectable count non-zero
#   -W D,I,C Monitor Temperature D)ifference, I)nformal limit, C)ritical limit
#   -v N,ST Modifies labeling of Attribute N (see man page)
#   -a      Default: equivalent to -H -f -t -l error -l selftest -C 197 -U 198
#   -F TYPE Use firmware bug workaround. Type is one of: none, samsung
#   -P TYPE Drive-specific presets: use, ignore, show, showall
#    #      Comment: text after a hash sign is ignored
#    \      Line continuation character
# Attribute ID is a decimal integer 1 <= ID <= 255
# except for -C and -U, where ID = 0 turns them off.
# All but -d, -m and -M Directives are only implemented for ATA devices
#
# If the test string DEVICESCAN is the first uncommented text
# then smartd will scan for devices /dev/hd[a-l] and /dev/sd[a-z]
# DEVICESCAN may be followed by any desired Directives.

smartctl ausgabe:

Code: 
server:~ # smartctl -a /dev/sda | grep Temperature
194 Temperature_Celsius     0x0022   110   106   000    Old_age   Always       -       37
 
RME

RME

Hallo,

Code: 
# The word DEVICESCAN will cause any remaining lines in this
# configuration file to be ignored: it tells smartd to scan for all
# ATA and SCSI devices.  DEVICESCAN may be followed by any of the
# Directives listed below, which will be applied to all devices that
# are found.  Most users should comment out DEVICESCAN and explicitly
# list the devices that they wish to monitor.
# Adding -d removable prevents error messages after disconnecting of
# monitored removable discs.
#DEVICESCAN -d removable
DEVICESCAN -d removable

# The word DEVICESCAN will cause any remaining lines in this
# configuration file to be ignored:
Zum Vergrößern anklicken....
Schieb Deine Befehle nach oben.

Gruss,
Roland
 
OP
F

Fendria

Ist leider immer noch in internen Werten...


Code: 
May 13 13:31:58 server smartd[26904]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 111 to 110
May 13 13:31:58 server smartd[26904]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 111 to 110
May 13 14:01:58 server smartd[26904]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 110 to 111
May 13 14:01:59 server smartd[26904]: Device: /dev/sda [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 110 to 111

allerdings jetzt scheinbar zweimal, wahrscheinlich verursacht dadurch dass der Devicescan die Festplatten dann nochmal hinzufuegt, oder?
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
Oben