lord_nilson
Newbie
Ich schaffe es nicht den Umax 610p zum laufen zu bringen. Ich habe in der dll.conf umax_pp ausgewählt! und was muss ich nun in der umax_pp.conf ändern?
Ich habe sane version 1.0.15
und wenn scanimage -L eingebe kommt das dabei raus:
linux:~ # scanimage -L
[sanei_debug] Setting debug level of dll to 255.
[dll] sane_init: SANE dll backend version 1.0.11 from sane-backends 1.0.15
[dll] sane_init: reading dll.conf
[dll] add_backend: adding backend `umax_pp'
[dll] sane_get_devices
[dll] load: searching backend `umax_pp' in `/usr/lib/sane'
[dll] load: trying to load `/usr/lib/sane/libsane-umax_pp.so.1'
[dll] load: dlopen()ing `/usr/lib/sane/libsane-umax_pp.so.1'
[dll] init: initializing backend `umax_pp'
[umax_pp_low] EPPsendWord610p failed, expected tmp=0xC8 , found 0xE8 (umax_pp_low.c:4735)
[umax_pp_low] SPPsendWord610p found 0x08 expected 0x88 (umax_pp_low.c:4616)
[umax_pp_low] SPPsendWord610p(zero) failed! (umax_pp_low.c:6287)
[umax_pp_low] initTransport610p() failed (umax_pp_low.c:6536)
[dll] init: backend `umax_pp' is version 1.0.603
[dll] sane_get_devices: found 0 devices
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `umax_pp's exit function
[dll] sane_exit: finished
Ich bedanke mich schonmal im voraus
MFG Daniel
Ich habe sane version 1.0.15
und wenn scanimage -L eingebe kommt das dabei raus:
linux:~ # scanimage -L
[sanei_debug] Setting debug level of dll to 255.
[dll] sane_init: SANE dll backend version 1.0.11 from sane-backends 1.0.15
[dll] sane_init: reading dll.conf
[dll] add_backend: adding backend `umax_pp'
[dll] sane_get_devices
[dll] load: searching backend `umax_pp' in `/usr/lib/sane'
[dll] load: trying to load `/usr/lib/sane/libsane-umax_pp.so.1'
[dll] load: dlopen()ing `/usr/lib/sane/libsane-umax_pp.so.1'
[dll] init: initializing backend `umax_pp'
[umax_pp_low] EPPsendWord610p failed, expected tmp=0xC8 , found 0xE8 (umax_pp_low.c:4735)
[umax_pp_low] SPPsendWord610p found 0x08 expected 0x88 (umax_pp_low.c:4616)
[umax_pp_low] SPPsendWord610p(zero) failed! (umax_pp_low.c:6287)
[umax_pp_low] initTransport610p() failed (umax_pp_low.c:6536)
[dll] init: backend `umax_pp' is version 1.0.603
[dll] sane_get_devices: found 0 devices
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `umax_pp's exit function
[dll] sane_exit: finished
Ich bedanke mich schonmal im voraus
MFG Daniel