=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10 family
Firmware Version: 3.AAC
User Capacity: 80.026.361.856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Oct 11 13:15:12 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 094 006 Pre-fail Always - 90623537
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3382
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 73629018
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 2343
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 3402
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 060 052 045 Old_age Always - 40 (Lifetime Min/Max 22/41)
194 Temperature_Celsius 0x0022 040 048 000 Old_age Always - 40 (0 19 0 0)
195 Hardware_ECC_Recovered 0x001a 092 072 000 Old_age Always - 149356583
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 6
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 45 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 45 occurred at disk power-on lifetime: 2290 hours (95 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 3f e4 c3 00 e0 00 00:00:29.249 READ DMA EXT
25 00 3f a5 c3 00 e0 00 00:00:29.248 READ DMA EXT
25 00 3f 66 c3 00 e0 00 00:00:29.248 READ DMA EXT
25 00 3f 27 c3 00 e0 00 00:00:29.247 READ DMA EXT
25 00 3f e8 c2 00 e0 00 00:00:29.246 READ DMA EXT
Error 44 occurred at disk power-on lifetime: 2290 hours (95 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 3f b2 b0 00 e0 00 00:00:27.291 READ DMA EXT
c6 00 10 01 00 00 ef 00 00:00:28.675 SET MULTIPLE MODE
91 00 3f 01 00 00 ef 00 00:00:28.675 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 01 01 00 00 e1 00 00:00:28.675 RECALIBRATE [OBS-4]
00 00 3f 00 00 00 00 04 00:00:28.675 NOP [Abort queued commands]
Error 43 occurred at disk power-on lifetime: 2290 hours (95 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 3f b2 b0 00 e0 00 00:00:27.291 READ DMA EXT
c6 00 10 01 00 00 ef 00 00:00:27.290 SET MULTIPLE MODE
91 00 3f 01 00 00 ef 00 00:00:27.289 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 01 01 00 00 e1 00 00:00:27.289 RECALIBRATE [OBS-4]
00 00 3f 00 00 00 00 04 00:00:27.288 NOP [Abort queued commands]
Error 42 occurred at disk power-on lifetime: 2290 hours (95 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 3f b2 b0 00 e0 00 00:00:27.291 READ DMA EXT
25 00 3f b2 b0 00 e0 00 00:00:27.290 READ DMA EXT
25 00 3f 73 b0 00 e0 00 00:00:27.289 READ DMA EXT
25 00 3f 34 b0 00 e0 00 00:00:27.289 READ DMA EXT
25 00 3f f5 af 00 e0 00 00:00:27.288 READ DMA EXT
Error 41 occurred at disk power-on lifetime: 2290 hours (95 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 3f b2 b0 00 e0 00 00:00:27.291 READ DMA EXT
25 00 3f 73 b0 00 e0 00 00:00:27.290 READ DMA EXT
25 00 3f 34 b0 00 e0 00 00:00:27.289 READ DMA EXT
25 00 3f f5 af 00 e0 00 00:00:27.289 READ DMA EXT
25 00 3f b6 af 00 e0 00 00:00:27.288 READ DMA EXT
SMART Self-test log structure revision number 1
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
