• Willkommen im Linux Club - dem deutschsprachigen Supportforum für GNU/Linux. Registriere dich kostenlos, um alle Inhalte zu sehen und Fragen zu stellen.

[gelöst]opensuse 13.1+Telekom Speedport LTE II

Hallo

hab gesucht, aber gibts zu viele Einträge zu Speedport
in wenigen Tagen wird DSL bei mir abgestellt und dann das Speedport freigeschaltet
gibt es eine dedailierte Hilfe, bzw erkennt Suse das Gerät selbständig?
vll auch auch link auf vorhandene Lösung *danke

mfg sweacher
 

Jägerschlürfer

Moderator
Teammitglied
wieso sollte Suse das Gerät nicht erkennen bzw. muss es das denn überhaupt?
Es wird doch genauso wie ein nirmaler Router mit dem Rechner verbunden (via LAN oder WLAN).
 
Hallo

LAN ist kein Problem
WLAN bekomme ich nicht hin
SSID gleicher Name, Verschlüsselung gleich, Verschlüsselungscode der, den mir von Netzwerkeinstellung gegeben wird
muss Drahtlos eigentlich sichtbar sein, damit es sich verbindet, oder ist unsichtbar auch ok?
Mit Netzwerkmanager habe ich es auch nicht geschafft

mfg
 
Hallo
weil ich gerade krank geschrieben bin und nochmal versucht hatte den Laptop via Funk mit dem Speedport zu verbinden.
Ich habe Speedport auf Macadresse "positiv" gestellt, Adresse des Laptop eingetragen.
Mag mir jemand helfen? Wie muss ichs einstellen?

mfg sweacher
 
Hallo
:???: ich habe http://www.opensuse-forum.de/allgemeines/tutorials-howtos/113-wlan-unter-opensuse-konfigurieren-und-einrichten/ gelesen und das auch genau nachvollzogen.
habe auch im BIOS des Laptop nachgesehen, WLAN ist eingeschaltet. Ich verstehe nicht, warum der Laptop nicht auf die Speedport zugreift

mfg ich brauch Hilfe
 
Oder gleich:
http://forum.linux-club.de/viewtopic.php?f=86&t=109291

Mit framps Script werden noch mehr Parameter abgefragt.
 
Hallo
vorab schonmal dies
Code:
# iwconfig eth0      no wireless extensions.
 wlp12s0   IEEE 802.11abg  ESSID:off/any             
Mode:Managed  Access Point: Not-Associated   Tx-Power=off              
Retry  long limit:7   RTS thr:off   Fragment thr:off           
Encryption key:off           
Power Management:off           
 lo       no wireless extensions.
Code:
# ifconfig 
eth0      
Link encap:Ethernet  Hardware Adresse 00:1D:09:C1:60:A1             
inet Adresse:192.168.1.3  Bcast:192.168.1.255  Maske:255.255.255.0           
inet6 Adresse: fe80::21d:9ff:fec1:60a1/64 Gültigkeitsbereich:Verbindung           
UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           
RX packets:4259 errors:0 dropped:0 overruns:0 frame:0           
TX packets:2790 errors:0 dropped:0 overruns:0 carrier:0          
collisions:0 Sendewarteschlangenlänge:1000           
RX bytes:5233883 (4.9 Mb)  TX bytes:315017 (307.6 Kb)           
Interrupt:17   
lo       
Link encap:Lokale Schleife             
inet Adresse:127.0.0.1  Maske:255.0.0.0           
inet6 Adresse: ::1/128 Gültigkeitsbereich:Maschine           
UP LOOPBACK RUNNING  MTU:65536  Metric:1           
RX packets:42 errors:0 dropped:0 overruns:0 frame:0           
TX packets:42 errors:0 dropped:0 overruns:0 carrier:0           
collisions:0 Sendewarteschlangenlänge:0            
RX bytes:2300 (2.2 Kb)  TX bytes:2300 (2.2 Kb)
Code:
# iwlist 
Usage: iwlist [interface] scanning [essid NNN] [last]               
[interface] frequency                
[interface] channel                
[interface] bitrate                
[interface] rate                
[interface] encryption                
[interface] keys                
[interface] power                
[interface] txpower                
[interface] retry                
[interface] ap                
[interface] accesspoints                
[interface] peers                
[interface] event                
[interface] auth                
[interface] wpakeys                
[interface] genie                
[interface] modulation

das script werde ich auch noch ausführen

mfg sweacher
 
Hallo
hier die Ausgabe des scriptes
und wieso keine ip? es ist dhcp eingestellt???
Code:
collectNWData.sh V0.7.5.1

--- Soll das Ergebnisfile in einem internationalen Forum gepostet werden (j/[n])?j
--- Welcher Netzwerkverbindungtyp soll getestet werden?
--- (1) Kabellose Verbindung (WLAN)
--- (2) Kabelgebundene Verbindung
--- Bitte mit 1-2 anworten:1

--- Welche Netzwerktopologie liegt vor?
--- (1) WLAN access point <---> LinuxClient
--- (2) WLAN HW router <---> LinuxClient
--- (3) WLAN access point <---> LinuxRouter <---> LinuxClient
--- (4) WLAN HW router <---> LinuxRouter <---> LinuxClient
--- Bitte mit 1-4 anworten:2

--- Bitte die WLAN SSID zu der verbunden werden soll eingeben (Wird in der Ausgabedatei maskiert):*******

--- NWCollect sammelt Netzwerkkonfigurationsinformationen in Datei ...
                                               
--- NWEliza untersucht das System nach häufigen Netzwerkkonfigurationsfehlern ...
!!! CND0120E: Die Netzwerkkarte wlp12s0 hat keine IP Adresse
!!! CND0490E: Kein Accesspoint mit der benutzen SSID auf dem Interface wlp12s0 gefunden
!!! CND0380E: Es wurden keine WLANs am Interface wlp12s0 gefunden. Die Hardware und/oder Treiber ist nicht richtig konfiguriert

mfg
 
Hallo
hier die Ausgabe des scriptes
Das ist nur die Ausgabe aus der Konsole, du solltest Dir übrigens das Posten in Code-Tags für Konsolenausgaben angewöhnen.

Poste bitte die entstandene Textdatei collectNWData hier, die enthält die kompletten Ausgaben.
 
Sauerland schrieb:
Hallo
hier die Ausgabe des scriptes
Das ist nur die Ausgabe aus der Konsole, du solltest Dir übrigens das Posten in Code-Tags für Konsolenausgaben angewöhnen.

Poste bitte die entstandene Textdatei collectNWData hier, die enthält die kompletten Ausgaben.

Ich weiß noch nicht wie und ob ich das richtig mache aber
Code:
iwlist scanning
eth0      Interface doesn't support scanning.

wlp12s0   Scan completed :
          Cell 01 - Address: 74:EA:3A:D1:A7:7A
                    Channel:1
                    Frequency:2.412 GHz (Channel 1)
                    Quality=18/70  Signal level=-92 dBm  
                    Encryption key:on
                    ESSID:"TPLINK_DO1"
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
                              12 Mb/s; 24 Mb/s; 36 Mb/s
                    Bit Rates:9 Mb/s; 18 Mb/s; 48 Mb/s; 54 Mb/s
                    Mode:Master
                    Extra:tsf=00000008703c5181
                    Extra: Last beacon: 3322ms ago
                    IE: Unknown: 000A54504C494E4B5F444F31
                    IE: Unknown: 010882848B960C183048
                    IE: Unknown: 030101
                    IE: Unknown: 050400010000
                    IE: Unknown: 2A0100
                    IE: Unknown: 32041224606C
                    IE: IEEE 802.11i/WPA2 Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : TKIP CCMP
                        Authentication Suites (1) : PSK
                       Preauthentication Supported
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (2) : TKIP CCMP
                        Authentication Suites (1) : PSK

lo        Interface doesn't support scanning.

Code:
[code]
collectNWData.sh V0.7.5.1

--- Which type of your network connection should be tested?
--- (1) Wireless connection (WLAN)

--- What's the type of networktopology?
--- (2) WLAN HW router <---> LinuxClient

--- On which host is the script executed?
--- (1) LinuxClient
--- WLAN SSID to connect to: §§§§§§§§1

--- NWCollect is collecting networkconfiguration information into file ...

--- NWEliza is analyzing the system for common network configuration errors ...
!!! CND0120E: Network card wlp12s0 has no IP address
!!! CND0490E: No access point with your SSID detected on interface wlp12s0
!!! CND0380E: No WLANs detected on interface wlp12s0. Hardware and/or driver not configured properly
!!! CND0450W: WLAN key masquerading is not fully tested on this distribution. Please check output file collectNWData.txt for visible WLAN keys and masquerade them manually

--- Go to http://www.linux-tips-and-tricks.de/CND to get more detailed instructions 
--- about the error/warning messages and how to fix the problems on your own.

--- If you are unsuccessful then place the contents of file collectNWData.txt in the net
--- (see http://www.linux-tips-and-tricks.de/CND_UPL for links) 
--- and then paste the nopaste link on your favorite Linux forum.

==================================================================================================================
===== cat /etc/*[-_]release || cat /etc/*[-_]version =============================================================
/etc/os-release
/etc/SuSE-release
NAME=openSUSE
VERSION="13.1 (Bottle)"
VERSION_ID="13.1"
PRETTY_NAME="openSUSE 13.1 (Bottle) (x86_64)"
ID=opensuse
ANSI_COLOR="0;32"
CPE_NAME="cpe:/o:opensuse:opensuse:13.1"
BUG_REPORT_URL="https://bugs.opensuse.org"
HOME_URL="https://opensuse.org/"
ID_LIKE="suse"
openSUSE 13.1 (x86_64)
VERSION = 13.1
CODENAME = Bottle
# /etc/SuSE-release is deprecated and will be removed in the future, use /etc/os-release instead
===== uname -a ===================================================================================================
Linux linux-pss8.site 3.11.10-25-desktop #1 SMP PREEMPT Wed Dec 17 17:57:03 UTC 2014 (8210f77) x86_64 x86_64 x86_64 GNU/Linux
===== cat /etc/sysconfig/network/ifcfg-[earwd]* | grep -v "^#|^$" | grep -v "=''" ================================
--- /etc/sysconfig/network/ifcfg-eth0
BOOTPROTO='dhcp'
NAME='BCM4401-B0 100Base-TX'
STARTMODE='auto'
USERCONTROL='no'
--- /etc/sysconfig/network/ifcfg-wlp12s0
BOOTPROTO='dhcp'
NAME='PRO/Wireless 3945ABG [Golan] Network Connection'
STARTMODE='auto'
USERCONTROL='yes'
WIRELESS_AP_SCANMODE='1'
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_DEFAULT_KEY=@@@@@@
WIRELESS_ESSID=@@@@@@
WIRELESS_KEY_LENGTH=@@@@@@
WIRELESS_MODE='Managed'
WIRELESS_POWER='no'
WIRELESS_WPA_PSK=@@@@@@
===== ping tests =================================================================================================
Ping of 8.8.8.8 failed
ping: unknown host www.google.com
Ping of www.google.com failed
===== cat /etc/resolv | grep -i "nameserver" =====================================================================
===== cat /etc/hosts =============================================================================================
127.0.0.1	localhost
===== (route -n && route -A inet6 -n) | egrep "(en|wl|eth|ath|ra|wlan|dsl|ppp)" ==================================
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
Kernel IPv6 Routentabelle
Ziel                                        Nächster Hop                                 Flags Metric Ref    Benutzer Iface
fe80::/64                                   ::                                      U     256    0        0 eth0    
ff00::/8                                    ::                                      U     256    0        0 eth0    
===== ifconfig (filtered for en|wl|eth|wlan|ra|ath|dsl|ppp) ======================================================
eth0      Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#1  
          inet6 Adresse: fe80::21d:9ff:fec1:60a1/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:9389 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7357 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:9472683 (9.0 Mb)  TX bytes:994388 (971.0 Kb)
          Interrupt:17 
===== lspci ======================================================================================================
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
	Subsystem: Dell Device [1028:01f2]
	Kernel driver in use: b44
--
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
	Subsystem: Intel Corporation Device [8086:1021]
	Kernel driver in use: iwl3945
===== lsusb | grep -v "root hub" =================================================================================
Bus 002 Device 002: ID 05a9:2640 OmniVision Technologies, Inc. OV2640 Webcam
===== hwinfo (filtered) ==========================================================================================
27: PCI 300.0: 0200 Ethernet controller
  Model: "Broadcom BCM4401-B0 100Base-TX"
  Vendor: pci 0x14e4 "Broadcom"
  Device: pci 0x170c "BCM4401-B0 100Base-TX"
  SubVendor: pci 0x1028 "Dell"
  SubDevice: pci 0x01f2 
  Driver: "b44"
  Driver Modules: "ssb", "b44"
  Device File: eth0
  Link detected: no
    Driver Status: b44 is active
    Driver Activation Cmd: "modprobe b44"
32: PCI c00.0: 0282 WLAN controller
  Model: "Intel PRO/Wireless 3945ABG [Golan] Network Connection"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x4222 "PRO/Wireless 3945ABG [Golan] Network Connection"
  SubVendor: pci 0x8086 "Intel Corporation"
  SubDevice: pci 0x1021 
  Driver: "iwl3945"
  Driver Modules: "iwl3945"
  Device File: wlp12s0
  Link detected: no
    Driver Status: iwl3945 is active
    Driver Activation Cmd: "modprobe iwl3945"
===== lsmod (filtered) ===========================================================================================
| ac              | af_packet       | arc4            | ata_piix        | b44              |
| bch             | bnep            | cfg80211        | coretemp        | dcdbas           |
| dell_laptop     | dell_wmi        | drm             | drm_kms_helper  | gpio_ich         |
| i2c_algo_bit    | i2c_i801        | iwl3945         | iwlegacy        | kvm              |
| lpc_ich         | mac80211        | memstick        | mfd_core        | mii              |
| mmc_core        | mperf           | mtd             | mxm_wmi         | nand             |
| nand_bch        | nand_ecc        | nand_ids        | nouveau         | r592             |
| r852            | rfkill          | scsi_dh         | scsi_dh_alua    | scsi_dh_emc      |
| scsi_dh_hp_sw   | scsi_dh_rdac    | sdhci           | sdhci_pci       | serio_raw        |
| sg              | shpchp          | sm_common       | sparse_keymap   | sr_mod           |
| ssb             | ttm             | usb_storage     | wmi             |
===== iwconfig ===================================================================================================
eth0      no wireless extensions.
wlp12s0   IEEE 802.11abg  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=off   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
===== ls /lib/firmware/*.{fw,ucode,bin} ==========================================================================
| agere_ap_fw.bin         | agere_sta_fw.bin        | ar5523.bin              | ar7010.fw                |
| ar7010_1_1.fw           | ar9170-1.fw             | ar9170-2.fw             | ar9271.fw                |
| ath3k-1.fw              | bnx2x-e1-4.8.53.0.fw    | bnx2x-e1-5.2.13.0.fw    | bnx2x-e1-5.2.7.0.fw      |
| bnx2x-e1h-4.8.53.0.fw   | bnx2x-e1h-5.2.13.0.fw   | bnx2x-e1h-5.2.7.0.fw    | carl9170-1.fw            |
| dvb-fe-xc5000-1.6.114.fw| dvb-usb-dib0700-1.20.fw | dvb-usb-terratec-h5-drxk.fw| f2255usb.bin             |
| htc_7010.fw             | htc_9271.fw             | intelliport2.bin        | iwlwifi-100-5.ucode      |
| iwlwifi-1000-3.ucode    | iwlwifi-1000-5.ucode    | iwlwifi-105-6.ucode     | iwlwifi-135-6.ucode      |
| iwlwifi-2000-6.ucode    | iwlwifi-2030-6.ucode    | iwlwifi-3160-7.ucode    | iwlwifi-3945-2.ucode     |
| iwlwifi-4965-1.ucode    | iwlwifi-4965-2.ucode    | iwlwifi-5000-1.ucode    | iwlwifi-5000-2.ucode     |
| iwlwifi-5000-5.ucode    | iwlwifi-5150-2.ucode    | iwlwifi-6000-4.ucode    | iwlwifi-6000g2a-5.ucode  |
| iwlwifi-6000g2a-6.ucode | iwlwifi-6000g2b-5.ucode | iwlwifi-6000g2b-6.ucode | iwlwifi-6050-4.ucode     |
| iwlwifi-6050-5.ucode    | iwlwifi-7260-7.ucode    | lbtf_usb.bin            | lgs8g75.fw               |
| mt7650.bin              | mts_mt9234mu.fw         | mts_mt9234zba.fw        | phanfw.bin               |
| ql2100_fw.bin           | ql2200_fw.bin           | ql2300_fw.bin           | ql2322_fw.bin            |
| ql2400_fw.bin           | ql2500_fw.bin           | rp2.fw                  | rt2561.bin               |
| rt2561s.bin             | rt2661.bin              | rt2860.bin              | rt2870.bin               |
| rt3070.bin              | rt3071.bin              | rt3090.bin              | rt3290.bin               |
| rt73.bin                | s2250.fw                | s2250_loader.fw         | tlg2300_firmware.bin     |
| tr_smctr.bin            | usbdux_firmware.bin     | usbduxfast_firmware.bin | usbduxsigma_firmware.bin |
| v4l-cx231xx-avcore-01.fw| v4l-cx23418-apu.fw      | v4l-cx23418-cpu.fw      | v4l-cx23418-dig.fw       |
| v4l-cx23885-avcore-01.fw| v4l-cx25840.fw          | vntwusb.fw              |
===== iwlist scanning (filtered) =================================================================================
No WLANs found
===== ndiswrapper -l =============================================================================================
No ndiswrapper module loaded
===== Active processes ===========================================================================================
wpa_supplicant:YES networkmanager:YES nm-applet:NO
===== ===== egrep -i "^[^#].*(persistent|networkmanager)" /etc/sysconfig/network/config ==========================
FORCE_PERSISTENT_NAMES=""
===== Actual date for bias of following greps ====================================================================
20:08:01 2015-04-03
===== grep -i radio /var/log/messages | tail -n 5 ================================================================
===== dmesg | grep -i radio | tail -n 5 ==========================================================================
===== tail -n 300 /var/log/messages | /usr/bin/grep -i firmware | tail -n 10 =====================================
===== egrep 'en|wl|eth|ath|wlan|ra|ppp' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/*persistent-net* ====
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#2", ATTR{type}=="1", NAME="wlp12s0"
===== egrep -r '(en.*|wl.*|eth|ath|wlan|ra)[0-9]+' /etc/modprobe.*|egrep -v -i '#|blacklist' =====================
/etc/modprobe.d/50-iwl3945.conf:options iwl3945 disable_hw_scan=1
/etc/modprobe.d/50-iwlagn.conf:options iwlagn 11n_disable=0
==================================================================================================================
*** NWElizaStates V0.7.5.1
PNIN:1 CFR:1 IF:eth0 IM:2 IF:wlp12s0 IM:1 DI:2 AP:0 FALON:1 NIC:1 cNiC:2:1 NI:2 cNI:2 NIW:wlp12s0-1 NDIS:0 CM:0 IP6:0 KM:0 0 WLW:0 RTDT:SuSE GUI:0 UID:0
[/code]
und wenn die Fehler gefunden sind, kann ich das auch löschen, damit es hier nicht zu voll wird

mfg
 

tomm.fa

.Linux Club Aushilfsadministrator
Teammitglied
sweacher schrieb:
Code:
What's the type of networktopology?
--- (2) WLAN HW router <---> LinuxClient
Hier hättest du WLAN Access Point wählen sollen.

sweacher schrieb:
Code:
===== Active processes ===========================================================================================
wpa_supplicant:YES networkmanager:YES nm-applet:NO
Sinnvoll wäre es, wenn du nur ein Werkzeug zur Konfiguration zur Einstellung des Netzwerks benutzt, entweder YaST, oder den NetworkManager (zur Zeit wird beides verwendet). Wenn du den NetworManager nutzt, dann musst du die Einstellungen unter YaST löschen, wie das funktioniert, erfährst du hier; möchtest du den Weg über YaST nutzen, dann andersherum und die Einstellungen im NetworkManager löschen.

sweacher schrieb:
und wenn die Fehler gefunden sind, kann ich das auch löschen, damit es hier nicht zu voll wird
Davor kann ich nur warnen, lasse es besser.
 
tomm.fa schrieb:
sweacher schrieb:
Code:
What's the type of networktopology?
--- (2) WLAN HW router <---> LinuxClient
Hier hättest du WLAN Access Point wählen sollen.

sweacher schrieb:
Code:
===== Active processes ===========================================================================================
wpa_supplicant:YES networkmanager:YES nm-applet:NO
Sinnvoll wäre es, wenn du nur ein Werkzeug zur Konfiguration zur Einstellung des Netzwerks benutzt, entweder YaST, oder den NetworkManager (zur Zeit wird beides verwendet). Wenn du den NetworManager nutzt, dann musst du die Einstellungen unter YaST löschen, wie das funktioniert, erfährst du hier; möchtest du den Weg über YaST nutzen, dann andersherum und die Einstellungen im NetworkManager löschen.

sweacher schrieb:
und wenn die Fehler gefunden sind, kann ich das auch löschen, damit es hier nicht zu voll wird
Davor kann ich nur warnen, lasse es besser.

Hallo
Code:
erfährst du [url=http://wiki.linux-club.de/opensuse/Netzwerkumstellung_unter_YaST_von_ifup/wicked_auf_NetworkManager]hier[/url];
Das habe ich gestern abend auch schon mal gelesen; Danke; ich möchte mit Yast und ifuip einrichten
Und ich lasse das Script nochmal durchlaufen mit WLAN Access Point

mfg
 
Hallo
habe das script nochmal laufen lassen. Und weil ich davon was im script gelesen habe, das Netzwerkkabel war ausgesteckt. Und den LAN-Zugang brauche ich (zumindest noch )

Code:
[code]
collectNWData.sh V0.7.5.1

--- Which type of your network connection should be tested?
--- (1) Wireless connection (WLAN)

--- What's the type of networktopology?
--- (1) WLAN access point <---> LinuxClient

--- On which host is the script executed?
--- (1) LinuxClient
--- WLAN SSID to connect to: §§§§§§§§1

--- NWCollect is collecting networkconfiguration information into file ...

--- NWEliza is analyzing the system for common network configuration errors ...
!!! CND0180I: The system can't ping external IP address 8.8.8.8
!!! CND0150E: There might be a problem with the default gateway definition 192.168.1.1 on interface eth0
!!! CND0130E: There is more than one network card defined in the same subnet: wlp12s0:eth0
!!! CND0360E: Wireless connection tested with an existing wired connection on interface eth0. Unplug the cable and execute the script again
!!! CND0450W: WLAN key masquerading is not fully tested on this distribution. Please check output file collectNWData.txt for visible WLAN keys and masquerade them manually

--- Go to http://www.linux-tips-and-tricks.de/CND to get more detailed instructions 
--- about the error/warning messages and how to fix the problems on your own.

--- If you are unsuccessful then place the contents of file collectNWData.txt in the net
--- (see http://www.linux-tips-and-tricks.de/CND_UPL for links) 
--- and then paste the nopaste link on your favorite Linux forum.

==================================================================================================================
===== cat /etc/*[-_]release || cat /etc/*[-_]version =============================================================
/etc/os-release
/etc/SuSE-release
NAME=openSUSE
VERSION="13.1 (Bottle)"
VERSION_ID="13.1"
PRETTY_NAME="openSUSE 13.1 (Bottle) (x86_64)"
ID=opensuse
ANSI_COLOR="0;32"
CPE_NAME="cpe:/o:opensuse:opensuse:13.1"
BUG_REPORT_URL="https://bugs.opensuse.org"
HOME_URL="https://opensuse.org/"
ID_LIKE="suse"
openSUSE 13.1 (x86_64)
VERSION = 13.1
CODENAME = Bottle
# /etc/SuSE-release is deprecated and will be removed in the future, use /etc/os-release instead
===== uname -a ===================================================================================================
Linux linux-pss8 3.11.10-25-desktop #1 SMP PREEMPT Wed Dec 17 17:57:03 UTC 2014 (8210f77) x86_64 x86_64 x86_64 GNU/Linux
===== cat /etc/sysconfig/network/ifcfg-[earwd]* | grep -v "^#|^$" | grep -v "=''" ================================
--- /etc/sysconfig/network/ifcfg-eth0
BOOTPROTO='dhcp'
NAME='BCM4401-B0 100Base-TX'
STARTMODE='auto'
USERCONTROL='no'
--- /etc/sysconfig/network/ifcfg-wlp12s0
BOOTPROTO='dhcp'
NAME='PRO/Wireless 3945ABG [Golan] Network Connection'
STARTMODE='auto'
USERCONTROL='yes'
WIRELESS_AP_SCANMODE='1'
WIRELESS_AUTH_MODE='psk'
WIRELESS_BITRATE='auto'
WIRELESS_DEFAULT_KEY=@@@@@@
WIRELESS_ESSID=@@@@@@
WIRELESS_KEY_LENGTH=@@@@@@
WIRELESS_MODE='Managed'
WIRELESS_POWER='no'
WIRELESS_WPA_PSK=@@@@@@
===== ping tests =================================================================================================
Ping of 8.8.8.8 failed
ping: unknown host www.google.com
Ping of www.google.com failed
===== cat /etc/resolv | grep -i "nameserver" =====================================================================
nameserver 192.168.1.1
===== cat /etc/hosts =============================================================================================
127.0.0.1	localhost
===== (route -n && route -A inet6 -n) | egrep "(en|wl|eth|ath|ra|wlan|dsl|ppp)" ==================================
Kernel IP Routentabelle
Ziel            Router          Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.1.1     0.0.0.0         UG    0      0        0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth0
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 wlp12s0
Kernel IPv6 Routentabelle
Ziel                                        Nächster Hop                                 Flags Metric Ref    Benutzer Iface
===== ifconfig (filtered for en|wl|eth|wlan|ra|ath|dsl|ppp) ======================================================
eth0      Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#1  
          inet Adresse:192.168.1.2  Bcast:192.168.1.255  Maske:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:64 errors:0 dropped:1 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:11875 (11.5 Kb)  TX bytes:6024 (5.8 Kb)
          Interrupt:17 
wlp12s0   Link encap:Ethernet  Hardware Adresse ##:##:##:##:##:#2  
          inet Adresse:192.168.1.3  Bcast:192.168.1.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:36 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 Sendewarteschlangenlänge:1000 
          RX bytes:6675 (6.5 Kb)  TX bytes:5724 (5.5 Kb)
===== lspci ======================================================================================================
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
	Subsystem: Dell Device [1028:01f2]
	Kernel driver in use: b44
--
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
	Subsystem: Intel Corporation Device [8086:1021]
	Kernel driver in use: iwl3945
===== lsusb | grep -v "root hub" =================================================================================
Bus 002 Device 002: ID 05a9:2640 OmniVision Technologies, Inc. OV2640 Webcam
Bus 003 Device 002: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Bus 003 Device 003: ID 413c:8126 Dell Computer Corp. Wireless 355 Bluetooth
Bus 003 Device 004: ID 0a5c:4502 Broadcom Corp. Keyboard (Boot Interface Subclass)
Bus 003 Device 005: ID 0a5c:4503 Broadcom Corp. Mouse (Boot Interface Subclass)
===== hwinfo (filtered) ==========================================================================================
27: PCI 300.0: 0200 Ethernet controller
  Model: "Broadcom BCM4401-B0 100Base-TX"
  Vendor: pci 0x14e4 "Broadcom"
  Device: pci 0x170c "BCM4401-B0 100Base-TX"
  SubVendor: pci 0x1028 "Dell"
  SubDevice: pci 0x01f2 
  Driver: "b44"
  Driver Modules: "ssb", "b44"
  Device File: eth0
  Link detected: no
    Driver Status: b44 is active
    Driver Activation Cmd: "modprobe b44"
32: PCI c00.0: 0282 WLAN controller
  Model: "Intel PRO/Wireless 3945ABG [Golan] Network Connection"
  Vendor: pci 0x8086 "Intel Corporation"
  Device: pci 0x4222 "PRO/Wireless 3945ABG [Golan] Network Connection"
  SubVendor: pci 0x8086 "Intel Corporation"
  SubDevice: pci 0x1021 
  Driver: "iwl3945"
  Driver Modules: "iwl3945"
  Device File: wlp12s0
  Link detected: yes
    Driver Status: iwl3945 is active
    Driver Activation Cmd: "modprobe iwl3945"
===== lsmod (filtered) ===========================================================================================
| ac              | af_packet       | arc4            | ata_piix        | b44              |
| bch             | bnep            | cfg80211        | coretemp        | dcdbas           |
| dell_laptop     | dell_wmi        | drm             | drm_kms_helper  | gpio_ich         |
| i2c_algo_bit    | i2c_i801        | ip_tables       | iwl3945         | iwlegacy         |
| kvm             | lpc_ich         | mac80211        | memstick        | mfd_core         |
| mii             | mmc_core        | mperf           | mtd             | mxm_wmi          |
| nand            | nand_bch        | nand_ecc        | nand_ids        | nouveau          |
| r592            | r852            | rfcomm          | rfkill          | scsi_dh          |
| scsi_dh_alua    | scsi_dh_emc     | scsi_dh_hp_sw   | scsi_dh_rdac    | sdhci            |
| sdhci_pci       | serio_raw       | sg              | shpchp          | sm_common        |
| sparse_keymap   | sr_mod          | ssb             | ttm             | wmi              |
===== iwconfig ===================================================================================================
eth0      no wireless extensions.
wlp12s0   IEEE 802.11abg  ESSID:"§§§§§§§§1"  
          Mode:Managed  Frequency:2.412 GHz  Access Point: ##:##:##:##:##:#3   
          Bit Rate=54 Mb/s   Tx-Power=15 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=70/70  Signal level=-19 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:30   Missed beacon:0
===== ls /lib/firmware/*.{fw,ucode,bin} ==========================================================================
| agere_ap_fw.bin         | agere_sta_fw.bin        | ar5523.bin              | ar7010.fw                |
| ar7010_1_1.fw           | ar9170-1.fw             | ar9170-2.fw             | ar9271.fw                |
| ath3k-1.fw              | bnx2x-e1-4.8.53.0.fw    | bnx2x-e1-5.2.13.0.fw    | bnx2x-e1-5.2.7.0.fw      |
| bnx2x-e1h-4.8.53.0.fw   | bnx2x-e1h-5.2.13.0.fw   | bnx2x-e1h-5.2.7.0.fw    | carl9170-1.fw            |
| dvb-fe-xc5000-1.6.114.fw| dvb-usb-dib0700-1.20.fw | dvb-usb-terratec-h5-drxk.fw| f2255usb.bin             |
| htc_7010.fw             | htc_9271.fw             | intelliport2.bin        | iwlwifi-100-5.ucode      |
| iwlwifi-1000-3.ucode    | iwlwifi-1000-5.ucode    | iwlwifi-105-6.ucode     | iwlwifi-135-6.ucode      |
| iwlwifi-2000-6.ucode    | iwlwifi-2030-6.ucode    | iwlwifi-3160-7.ucode    | iwlwifi-3945-2.ucode     |
| iwlwifi-4965-1.ucode    | iwlwifi-4965-2.ucode    | iwlwifi-5000-1.ucode    | iwlwifi-5000-2.ucode     |
| iwlwifi-5000-5.ucode    | iwlwifi-5150-2.ucode    | iwlwifi-6000-4.ucode    | iwlwifi-6000g2a-5.ucode  |
| iwlwifi-6000g2a-6.ucode | iwlwifi-6000g2b-5.ucode | iwlwifi-6000g2b-6.ucode | iwlwifi-6050-4.ucode     |
| iwlwifi-6050-5.ucode    | iwlwifi-7260-7.ucode    | lbtf_usb.bin            | lgs8g75.fw               |
| mt7650.bin              | mts_mt9234mu.fw         | mts_mt9234zba.fw        | phanfw.bin               |
| ql2100_fw.bin           | ql2200_fw.bin           | ql2300_fw.bin           | ql2322_fw.bin            |
| ql2400_fw.bin           | ql2500_fw.bin           | rp2.fw                  | rt2561.bin               |
| rt2561s.bin             | rt2661.bin              | rt2860.bin              | rt2870.bin               |
| rt3070.bin              | rt3071.bin              | rt3090.bin              | rt3290.bin               |
| rt73.bin                | s2250.fw                | s2250_loader.fw         | tlg2300_firmware.bin     |
| tr_smctr.bin            | usbdux_firmware.bin     | usbduxfast_firmware.bin | usbduxsigma_firmware.bin |
| v4l-cx231xx-avcore-01.fw| v4l-cx23418-apu.fw      | v4l-cx23418-cpu.fw      | v4l-cx23418-dig.fw       |
| v4l-cx23885-avcore-01.fw| v4l-cx25840.fw          | vntwusb.fw              |
===== iwlist scanning (filtered) =================================================================================
                    Channel:1
                    Frequency:2.412 GHz (Channel 1)
                    Quality=70/70  Signal level=-19 dBm  
                    ESSID:"§§§§§§§§1"
===== ndiswrapper -l =============================================================================================
No ndiswrapper module loaded
===== Active processes ===========================================================================================
wpa_supplicant:YES networkmanager:NO nm-applet:NO
===== Active WPA processes =======================================================================================
/usr/sbin/wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -u -f /var/log/wpa_supplicant.log
wpa_supplicant -iwlp12s0 -c/var/run/wpa_supplicant-wlp12s0.conf -Dnl80211,wext -P/var/run/wpa_supplicant/wlp12s0.pid -B
===== ===== egrep -i "^[^#].*(persistent|networkmanager)" /etc/sysconfig/network/config ==========================
FORCE_PERSISTENT_NAMES=""
===== Actual date for bias of following greps ====================================================================
20:38:23 2015-04-04
===== grep -i radio /var/log/messages | tail -n 5 ================================================================
===== dmesg | grep -i radio | tail -n 5 ==========================================================================
===== tail -n 300 /var/log/messages | /usr/bin/grep -i firmware | tail -n 10 =====================================
2015-04-04T20:10:34.134988+02:00 linux-pss8 kernel: [   47.406931] iwl3945 0000:0c:00.0: loaded firmware version 15.32.2.9
===== egrep 'en|wl|eth|ath|wlan|ra|ppp' /etc/udev/rules.d/*net_persistent* /etc/udev/rules.d/*persistent-net* ====
/etc/udev/rules.d/70-persistent-net.rules:SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="##:##:##:##:##:#2", ATTR{type}=="1", NAME="wlp12s0"
===== egrep -r '(en.*|wl.*|eth|ath|wlan|ra)[0-9]+' /etc/modprobe.*|egrep -v -i '#|blacklist' =====================
/etc/modprobe.d/50-iwl3945.conf:options iwl3945 disable_hw_scan=1
/etc/modprobe.d/50-iwlagn.conf:options iwlagn 11n_disable=0
==================================================================================================================
*** NWElizaStates V0.7.5.1
PNIN:1 CFR:1 IF:eth0 IM:2 IF:wlp12s0 IM:1 DI:2 AP:1 FALON:1 NIC:0 cNiC:2:0 NI:0 cNI:0 PNG:1 DR:1 NISS:1 IP6:0 KM:0 0 WLW:eth0 1 RTDT:SuSE GUI:0 UID:0
[/code]
mfg sweacher
 
Nach der Scriptausgabe
Code:
wlp12s0   IEEE 802.11abg  ESSID:"§§§§§§§§1" 
          Mode:Managed  Frequency:2.412 GHz  Access Point: ##:##:##:##:##:#3   
          Bit Rate=54 Mb/s   Tx-Power=15 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=70/70  Signal level=-19 dBm 
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:30   Missed beacon:0
funftioniert die Verbindung zu deinem AP einwandfrei.

Versuche die Kabelverbindung zu trennen und mach Neustart .

Nach dem Neustart öffne eine Konsole und als root tippe
Code:
iwconfig
Wenn jetzt neben ESSID: Name von deinem AP steht dann ist alles OK.

Falls immer noch die Internetverbindung fehlt dann wechsle im Yast zu Netzwerkmanager.
Ein ähnliches Problem ist hier gelöst: http://forum.linux-club.de/viewtopic.php?p=764763#p764763
 
Hallo Hans-Peter

Ja nach ESSIT steht der Name des Laptops. Ist ein Dell Inspiron 1720, der hat auch noch einen mechanischen WLAN-Scanner am seitlichen Gehäuse.
und eine dazugehörende Kontrollleuchte, und die leuchtet auch. Stelle ich diesen Schalter aber auf WLAN-Dauertbetrieb, dann geht die Kontrollleuchte aus.
Ich versuch mal den anderen Weg mit Networkmanager.
mfg
 
Hallo

ich habe tratitionell über ifup gelöscht, und den Networkmanager eingerichtet.
es rennt. Ich schreibe gerade mit WLAN ins Forum.
Danke und freundliche Grüße sweacher
 
Oben